查询词典 oil pressure

The discussion covers IMPCOCA110 gas carburator, ALTRONIC breakerless ignition system, and the safety features of KNG 3200E gas engines, including protective system, oil-pressure safety control, and water-level safety control.

本文主要介绍国内各油田用的小功率天然气机采用较多的美国IMPCO CA110型气体燃料混合器和ALTRONIC无触点点火系统以及日本KNG 3200E天然气机的安全保护装置、油压低停车装置和水位低停车装置的结构特点及工作原理，并提出有关发展天然气机的几点建议。

By using a new limit switch, and then on the machine: oil pressure recovery reached 0.4, oilway, correctingstudents'papers Kaitsu fuel dumping returned to normal, and the temperature of the surface of the pumb phases.

不纬换用一只陈的限位不开关后，再试机：油压复兴到达0.4，油路打、不收油的不静作皆复兴变态，且油泵暗地的温度也逐步落了上去。

Type electrolyzers,which were unaccurate regulation of elevation angle of extruder,poor adhension of unit cell gasckets and improper oil pressure of extruder,the corresponding preventive measures during installation were put forward.

针对ZBMCH-2.7电解槽运行中槽单元垫片错位挤出的3个原因：挤压机仰角调整不精确、单元垫片粘贴质量差和挤压机油压调整不当，提出安装过程的相应防范措施。

7 Type electrolyzer s,which were unaccurate regulation of elevation angle of extruder,poor adhension of unit cell gasckets and improper oil pressure of extruder,the corresponding preventive measures during installation were put forward.

针对ZBMCH-2.7电解槽运行中槽单元垫片错位挤出的3个原因：挤压机仰角调整不精确、单元垫片粘贴质量差和挤压机油压调整不当，提出安装过程的相应防范措施。

The traditional method such as pressing frozen out from the peel oil pressure, which will leave little residue, which makes product quality is poor.

比如传统的冷冻压榨法从果皮中压出的精油，其中会留下少许的残渣，这会使产品品质不佳。

Both kinds of power steering systems are actuated by oil pressure.

两种类型都是以油压为动力的。

When the diesel engine idles, engine oil pressure should not be less than 0.1MPa.

柴油机正常运转时，机油压力应在0.3～0.6MPa之间。

At the maximum luffing position check oil pressure, current and voltage when slewing.

4.2 安全工作负载试验SWL test 4.2.1 在吊臂与水平面成 60°位置处，检测绞车起升，下降动作的速度，油压，电流，电压等。

Aiming at the problems that oil pressure of existing P7100 type fuel injection pump can not meet the demand of the injection pipe fatigue test, on the basis of analysis and calculation, we designed a set of hydraulic integrated supercharging device.

针对现有 P7100型喷油泵出油压力不能满足喷油管疲劳性试验要求的问题，在分析、计算的基础上，设计出一套全液压集成式双作用增压装置；对其工作原理、结构特点进行了简要介绍，提出了系统集成化的设计思想，实现了各缸、阀、油路等元件的集成化。

Numerical analysis has been performed to understand the effect of journal and bearing block perturbation, inlet oil pressure on film reformation, rupture boundaries and the static characteristics of bearing.

2分析了轴颈、轴承座扰动和进油压力对边界条件和轴承静特性的影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。