查询词典 oil pressure

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

Through the experiment under different pressure and temperature, the influences of the supplied pressure and temperature to the oil film are obtained.

通过在不同压力和油温条件下的实验，分析了供油压力和供油温度不同时对油膜产生的影响。

The oil-filled line that was connected to the pressure gauge was still under high pressure.

充油线是连接到压力计仍是高压力下。

Otherwise, supply pressure can be kept steadily and the pressure vibration in the oil tank can be smoothed.

另外，成功解决了稳定压力源供给和压力输入造成油箱内的压力波动问题。

And has built the relations between pressure and pseud o-pressure,and the law distributed condensate oil content,when gas well is prod ucing from the reservoir.

利用凝析气藏等温衰竭过程中凝析油含量与随压力变化的数据确定出开采过程中储层内凝析油含量的分布特征。

Usually thedeeper section may sink mark . To prevent this defect it should set holdingpressure, The injection speed of holding pressure step is slow butwithin 40.C-60.C, If oil seal work on condition that high pressure anddamaged It's work time will be shorter, it can cause molding stable.

任何产品都不同程度的存在一个厚薄不一的问题，正常情况下，较厚的部分都可能存在一个收缩凹陷的现象，为了解决这种现象，就应应用到保压，保压一般来讲都应用较慢的射速，而压力的设置则应看缩水的情况如何，小到25%，大到80%都有可能。

The rheologic and non-Newtonian feature of lubricant that is used for elastic-plastic hydrodynamic lubrication is analyzed, under the condition of high pressure and large shearing strain ratio. The influence factors of oil film thickness and pressure forming during bar drawing are also discussed.

对于有限变形弹塑性有限元中求解非线性方程组的具体方法作了深入的探讨，提出了采用修正牛顿法时可应用过量修正技术加速其收敛效果，为有限变形弹塑性有限元的应用提供了新的计算方法。

With 3.0 t empty dual-use steam forging hammer, 1.0 t empty dual-use steam forging hammer, 750 kg, 400kg, 250kg, 150kg Kong Qichui a total of seven, made 3.0 t, 2.5t of a hammer plywood Taiwan, the construction of 2 m × 1.5m × 1.0m two large coal-fired furnace, a gas generator furnace, resistance furnace, Oil Furnace, Meilu stoves and other heat treatment of the four sets, with the following specs for Φ550 Saw 5,φ100 major fault Liu and other supporting material under the equipment, and has CW611250, T68, and other machining equipment, more than 60 species of vehicles, milling, planing, grinding, boring jobs complete, the main products φ820 × 60 × 1300 following the suppression of three products,φ273 high-pressure forging Billet-three links, all kinds of high-pressure-welded flange and 3.0 t following forging free, annual production capacity of 2400 t.

拥有3.0t空蒸两用模锻锤，1.0t空蒸两用模锻锤，750kg、400kg、250kg、150kg空气锤共7台，自制3.0t、2.5t夹板锤各1台，建造2m×1.5m×1.0m大型燃煤加热炉两座，煤气发生器加热炉1座，电阻炉、油炉、煤炉等热处理炉具各4套，拥有加工规格为Φ550以下锯床5台，φ100大型断料机等配套下料设备，且拥有CW611250、 T68等机加工设备60余种，车、铣、刨、磨、镗工种齐全，主要产品φ820×60×1300以下压制三通成品管，φ273高压锻制三通方坯，各种中高压平对焊法兰及3.0t以下自由锻件，年生产能力2400t。

According to a different purpose, N pinch and can be made of vacuum, pressure, pressure three, Wen stressed the form of a jacket, steam, conducting oil heating, water cooling and so on.

根据不同的使用目的，N捏和机可制成真空、压力、常压三种，温调形式采用夹套，蒸汽、导热油加热，水冷却等方法。

According to different purposes, NH Kneader can be made of vacuum, pressure, atmospheric pressure three; temperature tune the form of the use of jacket, steam, conducting oil heating, water cooling, etc.; material means there is hydraulic, double-cylinder for dumping, Ball material, such as screw extruder.

根据不同的使用目的，NH捏合机可制成真空、压力、常压三种；温调形式采用夹套，蒸汽、导热油加热，水冷却等方法；出料方式有液压、翻缸倾倒、球阀出料、螺杆挤压等。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。