查询词典 oil groove

The piston rings carried in the ring groove are of two basic types: compression rings and oil-control ring.

对活塞环进行的环槽有两种基本类型：压缩环和石油的控制环。

When No. 3 oil is used, put in 3000rpm, 8. 59Nm, the gear surface has an obvious plastic flow, an obvious groove is found on pitch line of the driving gear , an obvious edge is found on pitch line of the driven gear . The operating surfaces of both driving gear and the driven one is high in smooth finish, no pitting. Through the analysis on the gear surface only based on the gear in experiment with No.

实验的结果为：ISOVG68机械油作润滑油时，在输入3000rpm，5.96Nm时，齿面发现沿节线出现大面积的点蚀，且齿面有塑性变形；以3#油为润滑油时，在输入3000rpm，8.59Nm时，齿面发生了明显的齿面塑性流动，主动轮在节线处出现明显的沟槽，从动轮在节线处出现明显的棱脊，大小齿轮工作齿面均十分光洁，未发现点蚀现象发生。

The hole and oil groove on the rocker arm shaft should be downward.

摇臂轴上的孔和油槽应朝下。

There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oilhole on the cap of housings.

轴瓦内表面的不承担载荷部分开有油槽，润滑油通过进油孔和邮沟流进间隙。

On basis of the analysis for cores and well-logging, the authors have thoroughly studied the sedimentary facies types and characters of Chang 6 oil-bearing formation of the Baibao region with casting thin sections, SEM, trace elements and porosity and permeability analysis and a great deal of indoor testing data. The authors propose that the sedimentary facies type of Chang 6 oil-bearing formation of the Baibao region is a sublacustrine slump turbidite fan for the first time, and lithology is lower componential and textural maturities micro-fine feldspar sandstone primarily, with graded bedding, fluidified convolute bedding, slipping-cut and deformational structures, minitype syngenetic faults, flute cast, groove cast, load cast and other turbidite sedimentary facies signatures.

作者在岩心描述和测井分析基础上，结合铸体薄片、扫描电镜、重矿物、微量元素和孔渗分析等大量测试资料，对该地区长6油层组沉积相类型及特征进行深入研究，首次提出白豹地区长6油层组属于湖底滑塌浊积扇沉积体系，岩性以成分和结构成熟度均偏低的微－细粒长石砂岩为主，具粒序层理、液化包卷层理、滑动截切和变形构造、小型同生断层、槽模、沟模和重荷模等浊积沉积相标志。

As the factor of clearance, bearing chamfer, oil groove etc, The actual load is higher than theory of calculation.

由于受配合间隙、材料强度、轴承倒角、内部油槽等原因的影响，轴承的真正承载面压会大于理论计算值。

There are oil groove or holes on the outer ring which make HSB needle roller bearing easy for lubricating.

外圈上的油槽和油孔使HSB-滚针轴承加润滑油更加方便。

As the factor of clearance,bushes chemfer,oil groove etc.,the actually loadis higher than theory of calculation.

由于受配合间隙、材料强度、轴承倒角、内部油槽等原因的影响，轴承的真正承载面压会大于理论计算值。

Carbon steel machined slide bearings, the oil groove can be produced according to the bearings' working condition if needed.

以优质低碳钢为基体精加工而成的适用于重载低速环境恶劣工作部位的边界润滑轴套，轴套工作表面可按照工况条件加工出各种形式的油槽以起到充分润滑的作用。

Crack reasons for this are: the heating temperature is too high as a result of quenching or cooling in a hurry, the quality of thermal stress and metal volume changes in the organization of the anti-stress than the breaking strength of steel; the work of the original surface defects (such as surface micro-cracks or scratches) or the internal defect of steel (such as slag, serious non-metallic inclusions, white point, the residual cavity, etc.) formed in the quenching stress concentration; serious Decarburization and carbide surface segregation; parts after quenching Back lack of timely or tempering fire; processes in front of the stress caused by excessive cold red, forging folding, turning deep marks, sharp edges and corners, such as the oil groove.

造成这种裂纹的原因有：由于淬火加热温度过高或冷却太急，热应力和金属质量体积变化时的组织应力大于钢材的抗断裂强度；工作表面的原有缺陷或是钢材内部缺陷（如夹渣、严重的非金属夹杂物、白点、缩孔残余等）在淬火时形成应力集中；严重的表面脱碳和碳化物偏析；零件淬火后回火不足或未及时回火；前面工序造成的冷冲应力过大、锻造折叠、深的车削刀痕、油沟尖锐棱角等。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。