查询词典 odd element

According to practical work condition, section of a three segment hoist boom is self-determined with SECWRITE commands, then a finite element model is directly established in ANSYS environment with ANSYS finite element analysis software. Using Beam44 beam unit and node degree of freedom coupling technique to simulate connecting between each boom section and conduct finite element analysis, calculated result of stress deformation for the boom is obtained. The result from digital simulation is in relative coincidence with theoretical analytic result and the nonlinear decline occurrence in boom bending moment curve is explained.

以ANSYS有限元分析软件为工具，按吊臂实际工况，运用SECWRITE命令自定义三节吊臂截面直接在ANSYS环境下创建有限元模型，使用Beam44梁单元和节点自由度耦合技术模拟各节臂的连接，进行有限元分析，得到吊臂应力变形数值计算结果，数值模拟所得结果与理论解析解相吻合，解释吊臂弯矩图出现非线性下降的原因。

The main contents are as follows: Creating finite element model of cradle carriage, top carriage and trail of the howitzer. The structural static stress analysis of are dealt with finite element program system I-DEAS. For accuracy and computation cost, the nonlinear finite element structural dynamics model of the howitzer is created with different elements such as solid elements, shell elements and beam elements.

主要包括以下几个方面工作：建立了该炮摇架、上架和下架的三维有限元静力学模型，并应用I－DEAS有限元软件进行了强度分析；顾及计算准确性和计算成本，应用实体单元、壳单元和梁单元相结合的方法建立了该炮的非线性有限元结构动力学模型。

In practice, flat shell element can be constructed by the simple combination of new plate bending element with plane elasticity element.

在实践上可以将新板弯曲单元与已有的平面弹性单元简单叠合来构造平板壳单元；在理论上则概括为平行列式的概念，即平板壳单元的膜、板两部分在相互平行的位移函数空间和弯矩函数空间上分别列式。

This paper makes a three-dimensional model for QCM and analyzes directly the coupled phenomenon of the structural and electric fields of QCM with finite element analysis software ANSYS10.0. Through analyzing the convergence of the resonant frequency of QCM, the correctness of the finite element analysis is proved. The influence of different sizes of electrode on vibration of QCM and an optimal size of electrode is discovered, namely thickness of 100 nm and radius of 3 mm. The design of mesa on crystal plate is provided to solve the problem that the energy trapping is not good enough. This design proves valid based on finite element calculation and an optimal size of the mesa is given, namely height of 9.8 μm.

基于有限元分析软件ANSYS10.0对石英晶体微天平进行三维建模，验证了建模的正确性，并对不同电极结构尺寸进行仿真计算，对出现的耦合情况进行了分析，通过实验结果对比，提出较佳电极尺寸结构为厚度100 nm，半径3 mm；为解决金电极能陷效应不够理想的问题，提出在晶片上下表面筑平台的设计，有限元计算结果表明此设计能改善电极区的能陷效应，并且较佳平台高度为9.8μm。

Firstly the elastic stage of the cutting tool and workpiece in rectangular element is modeled and the relationship between the element node force and element node displacement also deduced.

首先选用矩形单元对刀具和工件弹性阶段进行有限元建模，得出其单元节点力和节点位移之间的关系，然后利用普朗特路斯方程，推导工件材料塑性变形时单元节点力和节点位移之间的关系，并指出金属由弹性变形到塑性变形时其单元刚度矩阵变化的规律，从而为实现金属切削过程的数值模拟提供可靠的理论基础。

The 3D Newtonian isothermal flow of normal double-thread screw element, normal triple screw element and VCR element was simulated.

第二部分则是在熔体输送段引入VCR元件，通过对常规双头螺纹元件、三头元件和VCR元件流道进行三维等温流场的模拟与分析。

The numerical analyses also showed that VCR element has the best distribute mixing effect and normal double-thread screw element take the second place, normal double-thread screw element is the weakest among them.

模拟结果表明：常规双头螺纹元件分散混合能力最强，常规三头螺纹元件次之，VCR元件最弱；而VCR元件分布混合能力最强，常规三头螺纹元件次之，常规双头螺纹元件最弱。

When one element of an N-element array is aberrated, the most sensitive aberration is Piston error, and then the sensitive aberrations are element defocus, tilt, spherical aberration, coma and astigmatism. As for four aperture system, the influence of Piston error is 2 times larger than that of defocus, and 4 times larger than that of astigmatism.

在合成孔径成像系统单个子孔径存在像差的情况下，Piston误差对系统的影响最大，其次是离焦误差、倾斜误差、球差、彗差和像散，对于四孔径系统，Piston误差对系统的影响几乎是离焦误差的2倍，像散的4倍。

As a result, some ideas about the fabrication are put forward.The EPMA experiment results show that the main element such as W, Mo, Ti, Ni, Cu, Fe element are changed gradually in W-Mo and W-Mo-Ti FGM. In the layer rich in W, the grain are intervained and are mixed mechanismly. The same is to the layer rich in Mo and W-Mo. These grain felt up by some sinter. In Mo-Ti layer rich in Mo, the grains are also mixed mechanismly. Ni, Cu, Fe element assembled at interface. Ni melt by Cu plays an vital role in sinter effect. The microstructure characteristics result show that the compactness of W-Mo and W-Mo-Ti FGM is good.

电子探针实验结果表明W-Mo系、W-Mo-Ti系梯度功能材料中主要元素W、Mo、Ti、Ni、Fe、Cu分布整体上具有梯度变化规律，发现富W区、富Mo区、W-Mo混合区中颗粒交错分布，基本上以机械混合的形式存在，颗粒之间主要靠烧结剂的粘结作用实现致密化；以Mo为主要组分的Mo-Ti混合区，也是以机械混合的形式存在；Cu溶解于Ni形成固溶体更好地起到活化烧结能力，Ni、Cu、Fe在宏观层间界面富集，有利于烧结致密化。

According to the shell finite element theory, the proposed method was based on the simulation of corrugated steel web by orthotropic plate element and that of flange plate by isotropic plate element respectively.

为了提高波形钢腹板箱梁的结构计算精度，本文根据板壳有限元理论提出了一种新的空间计算方法。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。