查询词典 numerical calculation

Based on the software of ANSYS with powerful function of nonlinear analysis and shell analysis, nonlinear numerical analysis is applied to "F" copper seal. The straight model, deflexed model and in flexed model were applied during calculation, and the responds were reflected during the joint deformation. Meanwhile, the rules of stress change and corresponding conclusion come out by comparing results between models.

2利用ANSYS强大的非线性和板壳分析功能，建立三维有限元模型，对&F&型止水铜片进行数值分析，分别给出直线模型、外拐模型以及内拐模型在接缝位移作用下的响应，通过模型间计算结果的对比，得出应力变化规律及相应的结论。

With the upgrade of the computer calculation and the development of finite element package, numerical simulation has become a very important method for in-depth study of the three-dimensional flow in screw extruders.

随着计算机计算能力的升级与有限元软件的发展，数值模拟方法已成为研究螺杆类挤出机流场的重要手段。

Online tuning and relatively light calculation burden due to directly coefficient setting by formula extend this scheme to be used for fast-running process and mechanical equipment, numerical simulation over a wide range of system parameter variation shows that the recommended scheme is superior to both traditional PDF designed by Phelans approach and relay feedback auto-tuning PID in terms of performance behavior.

本文通过基于继电反馈的自整定PDF控制和基于Phelan法的PDF控制及基于继电反馈的自整定PID控制的比较研究，表明所提出的控制方法具有良好的控制效果。

Online tuning and relatively light calculation burden due to directly coefficient setting by formula extend this scheme to be used for fast-running process and mechanical equipment, numerical simulation over a wide range of system parameter variation shows that the recommended scheme is superior to both traditional PDF designed by Phelan's approach and relay feedback auto-tuning PID in terms of performance behavior .

大量的数值仿真试验表明，该自整定PDF控制方法具有良好的控制效果和在线调节性能，具有设计公式简单、相对计算量小的特点，能够应用于快速变化的过程和机械设备中。本文通过基于继电反馈的自整定PDF控制和基于Phelan法的PDF控制及基于继电反馈的自整定PID控制的比较研究，表明所提出的控制方法具有良好的控制效果。

A physical model for numerical simulation and calculation of cross horizontal-tube falling film evaporator used in air-conditioning and refrigeration system was presented.

0前言早在1848年，水平管降膜式蒸发器技术就已经诞生，但是直到20世纪90年代，随着氟氯烃即CFC的逐步淘汰，才开始在制冷系统上被采用。

Finally, according to the researches of flume experiment and numerical simulation, the article puts forward a new method of flow rate calculation for the circular and pier shaped cylinder measuring flumes, which is much more application, and can meet the need of the free outflow and submerged discharge, meanwhile it analyses the precision of the new method, and provides the theory for the broad application of the circular and pier shaped cylinder measuring flumes.

最后，根据水槽试验和数值模拟研究成果，建立一套适用范围较广的、能满足自由出流和淹没出流需要的圆柱形和桥墩形量水槽的测流计算方法，并对方法的精度进行分析，为圆柱形和桥墩形量水槽的广泛应用提供理论基础。

The drag force between descending packed bed and gas flow is discussed by the drag coefficient of Ergun's equation. The calculation tool is ANSYS-CFX and the numerical method is finite volume method.

两相流中的阻力系数应用流体化床领域的Ergun's equation来探讨气体流经向下移动中的堆料床所造成的作用力。

The commonly-used capacity calculation approaches for ramp junctions are mostly based on the American HCM method, It had been approved that the headways for vehicles following the Weibull distribution function at on-ramp junctions in urban freeway system. The paper examined the critical headway and following time by the modified drew method and the survey traffic flow data on-site. The gap-acceptance capacity calculating model was developed for on-ramp junctions of urban freeway, and the numerical integration method was used to solving the model. Finally, the capacity values were obtained in condition of different mainline design speeds and different acceleration lane lengths.

针对目前国内外匝道连接段通行能力计算以美国HCM为主的现状和不足，研究发现城市快速路入口匝道连接段车头时距服从Weibull分布规律，利用改进的Drew方法及实际现场调查交通流数据确定了临界车头时距和随车时距，建立了城市快速路入口匝道连接段通行能力的间隙接受计算模型，并利用数值积分法进行计算和求解，从而得到了主线不同设计速度及不同加速车道长度条件下的城市快速路入口匝道连接段可能通行能力值。

The heat conductivity calculation has been divided into two parts, form the borehole to the exposure of cement mantle and in the formations, as for corresponding to different borehole structures, different methods have been adopted to sum the overall heat transfer coefficients and numerical method is used to calculate the heat loss on each nodal point, furthermore, through the model proposed herein, the degrees of influences of different borehole structures on heat loss could be calculated in order to get the most economic and efficient borehole structure.

把导热分为井筒到水泥环外壁和地层导热两部分计算，对不同的井筒结构采用不同方法计算总传热系数，数值法求解每个节点处的热损失，并通过模型对比计算了不同井筒结构对井筒热损失的影响程度，得到最经济有效的井筒结构。

On the basis of instantaneous forced analysis to short circuit of power transformer and numerical value calculation using low voltage impulse analysis, the paper presents the essentiality of winding distortion after short circuit of power transformer. By contrasting the three main ways of the world such as low-voltage impulse、 short circuit impedance analysis and frequency response analysis , FRA is adopted for distortion testing. Then we design a new testing instrument of transformer winding distortion—testing system of transformer winding distortion.

本文首先在对电力变压器短路时的瞬时受力分析及所受电磁力的有限元法的数值计算的基础上，论证了电力变压器短路以后进行绕组变形测试的必要性；然后通过比较的方法对目前国内外主要使用的三种方法：低压脉冲法、短路阻抗法和频率响应法，进行了一一对比，并根据对比结果，确定在本课题中使用频响法；最后在理论研究的基础上，设计出了一种新型的变压器绕组变形测试仪——电力变压器绕组变形测试系统。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。