查询词典 nozzle

The nozzle water pressure, the bottle washing temperature and the contact time are subject to the standards recommended by the manufacturer of bottle washers.

喷嘴水压、洗瓶温度及接触时间应按照洗瓶机制造商所推荐为标准。

Solid wimble nozzles are commonly used as flushing nozzles at home and abroad,and the uniformity of spray is one of the important indexes for the performance evaluation of a flushing nozzle.

国内外除雾器冲洗喷嘴一般均采用实心锥喷嘴，均匀度是考核喷嘴性能的重要指标之一。

Case studies: this phenomenon is clearly the influence of the suction, when there are suction paper of slow, with no suction paper notes, under the wind pump started gripper suction nozzle provided exceeds the ceiling exists, the wind pump customs without suction, under no overpressure condition suction exists.

案例不分析：这种本体澄辉是呼风的感化，当有呼风时纸下的缓，无呼风时纸下的迟，表明风泵开动后递纸呼嘴足够呼活命，风泵盖后，而无呼风，无缺呼本体活命。

B the nozzle without wind question: with regard to this problem, first check the wind pump is in work, and then verify whether the increase in the stack to the correct location, in front of the stack must be of induction head stack obscured paper machine starts running, the wind began to sucker.

B。吸嘴无风题目：对于这个题目，请不后查抄风泵是否在处事，然后查抄纸堆是否跌落到侧确场所，纸堆后背的感答足务必被纸堆遮盖，板滞不休运动动纸步调时，吸嘴风才不休投递。

The spray-rinsing tank is located on production line, on which the stainless steel working tank, spray pipeline, spray nozzle s, support rolls and wringer rolls etc.

喷淋槽在生产线中，装有不锈钢的工作槽、喷淋管道、喷嘴、支撑辊和挤压辊等

010 Failed to move the Z-axis to the nozzle inspection sensor position.

无法移动Z轴到吸嘴感应器检测位置。

Production and size determination of large size atomic clusters A gas jet of clusters was produced when a high backing pressure rare gas adiabatically expanded into vacuum through a home-made double solenoid pulsed valve and a conic nozzle.

高背压惰性气体经由自行设计研制的双线圈高速脉冲气阀和锥型喷嘴向真空绝热超声膨胀，形成团簇喷流。

Said pressurised air current can be generated by a pressurised air nozzle (32) whose outlet (33) is situated adjacently and directly on the output side of the clamping device.

此压缩空气流可通过一压缩空气喷嘴（32）来产生，它的喷口（33）直接靠近夹紧装置的出口位置。

After several practical problems are resolved,the relation between contents of S,Si and Al has been disclosed.The ratio of Ca to Alin in steel is 1.26∶1 after calcium treatment,the nozzle clogging does not happen and the consumption of calcium is reduced.The recovery factor fluctuation of boron are 64% and ±5×10-6, respectively.

通过硼微合金化若干工艺问题的解决和工艺优化，明确了钢水硫含量、增硅、铝控制之间的内在关系；使SPHC钢成分合格的同时，实现硼收得率达到64%，硼的质量分数波动±5×10-6；钙处理达到钢水中w∶w为1.26∶1时，确保水口浇注顺利，同时节省钙线用量。

The experimental results show that the mean particle size of griseofulvin precipitated by RESS is smaller than 1, 0μm, narrow distribution and 95％ fine particles is smaller than 1. 0μm. Increase of the pre-expansion pressure, the extraction temperature, the expansion chamber temperature, the spraying distance, the concentration of cosolvent and decrease of the nozzle diameter resulted in decrease of the particle size under the operating condition studied. Enhancement of the pre-expansion temperature resulted in increase of the particles size. The SEM of GF shows that the shape of original is atactic and a wide size distribution, but the microparticles obtained by RESS is reverse. Similar melting points and XRD patterns were observed for the original material and the precipitates obtained by RESS.

实验结果表明，用含夹带剂的RESS法制备的灰黄霉素微粒的平均直径在1μm左右，且分布均匀，95％微粒在1μm以下，仅用CO〓作为超临界流体制备的微粒与上述方法制备的微粒的平均直径和分布相似，只是产量太低，而用机械法制备的微粒平均直径在3μm左右且分布较宽；不同的过程参数对沉析微粒尺寸有不同的影响，预膨胀压力、膨胀室温度、溶解温度以及夹带剂浓度的提高或增大，均可使沉析微粒的直径变小；预膨胀温度提高，所得微粒的直径变大；喷射距离的增加，沉析微粒的直径变小；喷嘴直径越小，由此制得的微粒的直径就越小；根据实验结果还可知道，通过理论计算的马赫盘处微粒的直径可以较好地估计出膨胀室中收集到的微粒的直径。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。