查询词典 nectar-bearing

Using a drum Cr18Ni9Ti furnace tank made of stainless steel cylinder, or a Cr-Mn nitrogen heat-resistant steel castings, by the end of the furnace body, bearing bearing supports, and with a motor-reducer for use furnace tank to the slow rotation, with drum parts Rotation of the tank furnace heated evenly, and the workpiece between each other without coverage phenomenon, the same color after heat treatment furnace can feed the other end to the mouth from two roller bearing.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

Because the support position of bearing has great effect to the frequency of coupled vibration of shafting, this paper researches the dynamic alignment problems of shafting at first so as to determine the support position of bearing rationally, especially the position of stern tube bearing.

由于轴承的支承点位置对轴系的耦合振动频率影响很大，所以本文首先研究了轴系的动态校中问题，以合理确定轴承特别是艉管轴承的支承点。

The first step is separating bearing one by one to be weighing, then the microcontroller decide whether current bearing is good or bad based on the weighing data from the balance, make the electric magnate move to distinguish the good bearing from bad ones.

这是称重法的必由之路；第二步根据称重天平串口传来的数据，经由单片机判断控制继电器动作，实现轴承的分拣。同时讨论了对关键部件，轴承排序机构上，中，下盖的材料选取及主轴与带传动的设计方案。

Bearing rapid industrial development, relies on the market bearing the country's largest - Shandong smoke shop the market, building a low-speed machining with micro-bearing, up to 5 kilometers, located 45 enterprises, 13 villages, processing one billion sets of bearings, annual output value reached 520 million yuan.

轴承产业发展较快，依托全国最大的轴承市场——山东烟店市场，建设了低速微型轴承加工带，长达5公里、入驻企业45家、专业村13个，年加工轴承10亿套，年产值达到5.2亿元。

All you have to do to get the back bearing in position is slide the drive shaft through the bulkhead bearing, slide the bulkhead in place and then tack the stern bearing in perfect center.

所有你必须做，以获得回轴承在立场是滑动传动轴通过舱壁轴承，滑动舱壁在的地方，然后钉在艉轴承在完美的中心。

The dynamic performance equations for flexible rotor-bearing system are eshablished, the dynamic analysis for the rotor bearing system is carried out, the influence of mechanical seals to forced and self-exciting movement of rotor-bearing system is presented.

建立了柔性转子轴承系统的运动方程，对水轮机转子－轴承系统进行了动力学分析，确定了机械密封对转子－轴承系统动力学性能的影响。

According to fully expounding the geologic condition of the location of the bridge and the structure of pile foundation and the research level of the bearing capacity of group pile foundation in the present, the paper analyzes the mechanism of group effect and the impact on bearing capacity of pile foundation. The finite-element numerical analyses and self-balanced method are adopted in the present paper to calculate and analyze the vertical bearing capacity of pile group of north main-tower is cleared up and analyzed.

在全面阐述桥位区工程地质条件和桩基础组成结构以及群桩基础承载力研究现状的基础上，深入探讨了群桩效应及其对桩基础承载力影响的机理，分别采用自平衡试桩测试技术和三维土工有限元模拟方法研究了单桩竖向承载力问题，通过对试验和计算结果的整理、对比分析，确定了能够客观反映地基土工程特性的地基土计算参数。

In order to solve the poor load capacity of oil film bearings during the start-up process of tandem cold rolling mills, based on the hydrostatic bearing theory, a load bearing capacity model for oil film was established. The influences of screw-down tilting, hydraulic pump power and restrictor's hydraulic resistance on the hydrostatic pressure bearing-spindle system were calculated.

针对某CVC带钢冷连轧机启动阶段支持辊油膜轴承静压承载能力不足的问题，应用流体润滑理论，建立了轴承倾斜工作下静压承载能力的全润滑系计算模型，分析了轧机压下倾斜、油泵功率和节流器液阻对轴承静压承载性能的影响。

Bearing and shaft fastening methods are: the outer sleeve with eccentric spherical bearing, the eccentric sets Presentation at the bearing inner ring of the eccentric stage, along the axis of rotation direction of tightening eccentric sleeve, and then wrench tighten the screw Hexagon eccentric sleeve on the set screws can be.

轴承与轴的紧固方法是：对带偏心套的外球面轴承，将偏心套套在轴承内圈的偏心台上，沿轴的旋转方向拧紧偏心套，再用内六角螺钉扳手拧紧偏心套上的紧定螺钉即可。

Anda Bearing Corp. Ltd. is located at the side of No.330 national highway in Lishui, Zhejiang Province. It covers more than 5,000 square meters with beautiful view in and round the factory. The company has more than 30 years of engine processing history. It focuses on producing various bearings including:1. Linear movement ball bearing series: standard type, adjustable gap type, opening type, flange attached type;2. CF screw nut rolling wheel and rolling needle bearing series

安达轴承有限公司座落在秀山丽水的交通要道330国道旁，占地面积5000多平方米，厂区内环境优雅，是花园式工厂，本公司有三十多年机械加工历史，专业生产杆端关节轴承、直线运动球轴承、螺栓型滚轮滚针轴承、向心关节轴承，广泛用于自动化设备、印刷、包装、矿山、冶金、食品、电动工具、电力、轻工、航天等各种工业机械配套的专用轴承。

The work of this paper is as follows: 1. Looking back the progressing history of the linear motor, introducing the features of the elevator driven by linear induction motor, radicating the topic of this paper "the digital frequency variable control of the elevator bi-side direct driven by linear induction motor". The research of this paper covers the conventional VVVF control, space vector based VVVF control, vector control and DTC.

本文主要开展了以下几个方面的工作： 1 回顾了直线电机发展历史，电机的驱动技术演变，特别是针对直线电机的驱动，简要介绍了直线感应电机驱动电梯的优点和不同结构类型，对传统的v／f控制，基于空间矢量法的v／f控制，矢量控制，和基于电压空间矢量的直接转矩控制进行了比较，确立了本课题的研究主题：直线感应电机双边直推式驱动电梯的全数字变频控制。

The article combines with the treatment of a superficial civil air defense work to introduce how the grouting method to improve the performance of the backfill soil.

文章从治理漂浮人防工事的角度提出了注浆技术在改善回填土性质方面的应用，并详细阐述了注浆技术的施工流程。