查询词典 nearest relative

The structural and mechanical properties of ring-spun yarn have been studied comprehensively. The relationships between yarn linear density, yarn twist, and the relative yarn structural and mechanical properties have been obtained. Through statistical analysis of yarn linear density, twist, and strength of 200 groups of pure cotton yarn, and considering some influence factors, such as carded or comed, application of long-staple cotton, experiential functions of yarn relative strength with yarn linear density and twist have been obtained.

对环锭纱结构力学性能进行系统研究，得出环锭纱的相关力学性能参数与纱线线密度和捻度的关系；通过对从工厂收集的200组纯棉纱线线密度、捻度、强力等数据的统计分析，并综合考虑纱线线密度、是否精梳、是否使用长绒棉等因素，得出了线密度和捻度与纱线强力相对值的经验函数关系。

The occurrences, relative abundance, relative density, most common and longest SSRs in the three species were analyzed and compared with each other. The results revealed that the SSRs number in B. japonicum, M. loti and S. meliloti genomes were 1410, 859 and 638, respectively. In the three genomes, tetra-, penta-and hexa-nucleotide repeats were more abundant, indicating higher mutation rates in these species.

大豆慢生根瘤菌、百脉根根瘤菌和苜蓿中华根瘤菌基因组中的SSRs分别为1410个、859个和638个，3种根瘤菌基因组中长重复的四、五、六核苷酸基序更为丰富，变异性更高。

2Combined design data of rapid-fire guns,the machine structure have beenabstracted reasonable computation model of reduction.The equations thatdescribe relative motion and relative force about between moveable elements havebeen deduced.

2根据某型自动火炮的设计资料并进行合理的简化将具体的机械结构抽象成合理的计算模型，推导出描述自动机可动部件之间相互作用及相对运动的具体表达式。

MACR and MVK continued to react with ozone to form MG and other products and disappeared finally under the experimental conditions, so their yields relative to isoprene conversion were variable along the reaction time, with the maximum yields observed as 0.33±0.02 for MACR and 0.21±0.02 for MVK respectively. MG, HCHO, HCOOH, CO and CO2 are inactive to ozone, and their final yields relative to isoprene conversion were 0.48±0.03, 0.87±0.03, 0.49±0.03, 0.60±0.03 and 0.65±0.10, respectively.

由於MACR和MVK继续与O3反应直至完全，它们的产率随时间而变化，反应过程中观测到的最大产率分别为0.33±0.02和0.21±0.02；而MG，HCHO，HCOOH，CO和CO2不与O3发生反应，最终产率分别为0.48±0.03，0.87±0.03，0.49±0.03，0.60±0.03和0.65±0.10。

The electromagnetic loss property was studied by the relative dielectric constant and relative magnetic permeability of the ferrites.

并测试样品的相对介电常数和相对磁导率，研究了它们的电磁损耗特性。

At the same time, the system integrates the theories ofKBE, sufficiently utilizing correlative relative knowledge design and expertexperiences in relative fields and using CATIA V5 standard interface, thesystem is good of man-computer interaction and can be used conveniently. Thissystem basically comes to realization of intelligence, increases work efficiencyin car body layout design and is very practical.

在编制过程中结合"基于知识的工程"思想，使各个模块充分利用相关设计知识和相关领域专家经验，采用CATIA V5标准界面，利用二次开发实现专用的工具条和图标，具有很强的人机对话能力，操作使用方便，初步实现了轿车车门布置系统的智能化，提高了轿车车身布置设计的工作效率，具有很强的实践性。

The obtained maximum relative standard deviation was 5.89%, and relative errors were -20.99%-15%.

实验结果表明，测量结果的相对标准偏差最大为5.89%，相对误差在-20.99%～15%范围内，说明对铝合金样品成分进行定量分析，激光诱导击穿光谱是一种有效的光谱分析工具，但是分析结果的准确度仍需要提高。

The model description language and relative technologies and theories on dynamics modeling of mechanical system based on the language are studies in this paper, and relative functions are fulfilled in InteDyna.

本文在国家八六三计划(2004AA411010)与国家科技攻关计划(2004BA201A85)的资助下，开发多体动力学仿真分析平台——InteDyna，深入研究了模型描述语言和基于模型描述语言的机械系统动力学建模的技术与理论，并在InteDyna系统中实现了相应的功能，为复杂机械产品的建模分析提供方便。

The low-temperature peak corresponds to the minimum of relative dynamic modulus and is attributed to elastic modulus softening effect caused by the anelastic motion of the phase interface. The high-temperature peak corresponds to the inflexion point of relative dynamic modulus and the volume change produced by the normal motion of the phase interface is responsible for the peak.

低温内耗峰对应于相对动力学模量曲线最小值，是相界面切向滞弹性运动引起的模量软化所致；高温内耗峰对应于相对动力学模量曲线拐点，是相界面法向运动引起的体积变化所致。

An injection mechanism for an injection molding machine, including a front plate carrying an injection cylinder; a guide rod arranged fixedly relative to the front plate and having a longitudinal guiding axis; a movable plate arranged movably relative to the front plate along the guiding axis and carrying an injection screw; and a rear plate arranged at a location opposite to the front plate with the movable plate disposed therebetween.

一用于注射成型机的注射机构，包括：一支承压射缸的前板；一相对于所述前板固定布置并限定出一纵向导轴的导杆；一沿所述导轴相对于前板可动布置并支承注射螺杆的可动板；一布置在与所述前板相对位置上的后板，可动板布置在它们之间。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。