查询词典 moulding

The production capacity of moulding machine with sawdust as raw material arrives to 250 kg/h.Used as house heating-fuel, the pelleted fuels can make good economical benefits and obvious social benefits.

研究开发的成型机以木屑为原料生产能力达250 kg/h，当颗粒成型燃料作为家庭取暖炉用时，具有较好的经济效益和明显的社会效益。

The technique comprises the steps as follows: using the waste filtered mud of the sugar-refinery as the material to generate gas which is dehydrated till the water content is less than and equal to 30 percent and through distribution (clay used for of 70.00 to 85.0 percent, dehydrated filtered mud of the sugar-refinery of 15.0 to 30.0 percent, intensifier carboxymethyl cellulose or propyloic fibrin is 0.1 percent of the total dosage of the below material), performaing, moulding with high temperature (800 to 1200 DEG C, 20 to 180min) and acquiring the multi-hole porcelain granule with 20 to 30 percent of poriness, 10 to 20 percent of water absorbing capacity and 1.5 to 7.5/MPa of cylinder pressing intensity.

一种糖厂滤泥生产多孔陶粒技术，是用糖厂废弃物滤泥为发气原料，经脱水至含水≤30％，经配料(陶瓷用黏土70.0～85.0％，糖厂脱水滤泥15.0～30.0％，增强剂羧甲基纤维素或羧乙基纤维素为上述原料总量的0.1％)、制坯、高温(800~1200℃，20～180min)成型，得到孔隙率20~30％、吸水率10~20％、筒压强度1.5~7.5/MPa的多孔陶粒。

On one hand we take the waste gypsum, pyritic slag as the main resources. Proportion is such as follows: scree 15%, pyretic slag 30%, waste gypsum 45%, cement 10%, then take the semi-dried method, high pressure moulding to produce the waste gypsum and pyrite cinder brick which resist pressure is over 100~# brick resist pressure.

实验一方面以工业废石膏和硫酸烧渣为主要原料，按石屑15%，硫酸烧渣30%，废石膏45%，胶结料10%；半干法高压成型，再自然养护，制成废石膏硫酸烧渣砖，强度达到100~#以上。

Our company has strong technology and advanced equipments such as Automatic Moulding System(Disa230B), Sinto ACE5, Advanced Automatic Pouring Equipment, EIRICH Automatic Sand Mixer, kinds of meaurement equipments(ARL Spectrometer, CMM, Magnetic Particle Inspection Machine and so on), Machining Center(200sets), CNC Lathe(400sets), Drilling Machine(200sets) and machines for surface treatment.

本公司具备雄厚的技术力量跟先进的生产设备。铸造： DISA造型系统(DISA230B)、新东ACE5 、先进的自动浇注设备，EIRICH 自动混砂机及各种检测设备(ARL 分光仪、CMM 、磁粉探伤仪等)，加工：加工中心(200台)、CNC车床(400台)、钻床(200)；及表面处理。

Vtp pulley can be widely used in compressors, agriculture machines and other industrial machines which require high speed transmission.our company has strong technology and advanced equipments such as automatic moulding system(disa230b), sinto ace5, advanced automatic pouring equipment, eirich automatic sand mixer, kinds of meaurement equipments(arl spectrometer, cmm, magnetic particle inspection machine and so on), machining center(200sets), cnc lathe(400sets), drilling machine(200sets) and machines for surface treatment.

它主要应用于压缩机、农机、以及工业机械上需要高转速的传动设备，每秒线速度可达100米以上。本公司具备雄厚的技术力量跟先进的生产设备。铸造： disa造型系统(disa230b)、新东ace5 、先进的自动浇注设备，eirich 自动混砂机及各种检测设备(arl 分光仪、cmm 、磁粉探伤仪等)，加工：加工中心(200台)、cnc车床(400台)、钻床(200)；及表面处理。

Our company has strong technology and advanced equipments such as Automatic Moulding System(Disa230B), Sinto ACE5, Advanced Automatic Pouring Equipment, EIR IC H Automatic Sand Mixer, kinds of meaurement equipments(ARL Spectrometer, CMM, Magnetic Particle Inspection Machine and so on), Machining Center(200sets), CNC Lathe(400sets), Drilling Machine(200sets) and machines for surface treatment.

铸造： DISA造型系统(DISA230B)、新东ACE5 、先进的自动浇注设备，EIR IC H 自动混砂机及各种检测设备(ARL 分光仪、CMM 、磁粉探伤仪等)，加工：加工中心(200台)、CNC 车床(400台)、钻床(200)；及表面处理。

The easiest solution is to notch butt join the skirtboard and riser and use a piece of handrail fillet or other moulding to cover the joint between the riser and skirtboard.

最容易的解决办法是加入skirtboard缺口对接、喉和使用一块脊肉扶手等造型之间的联合采访，并skirtboard喉。

Lifting was the main component of moulding process with over 50%MVC EMG activity. The sEMG of erector spinae muscles was abnormal in moulders with low back pain during work.

造型作业中又以搬举动作肌电活动最高，超过了最大随意收缩的50％，有的搬举指数为NIOSH推荐值的4-5倍，且腰背痛的造型工人在作业期间，竖脊肌肌电活动与非腰背痛者明显不同。

The mian works are as follows:(1)By coprecipitation technique and coprecipitation- gel technique the nano zirconia powder was produced, factors affecting the properties of nano zirconia powder such as pH and the content of stabilizator are analyzed;(2)By the new pressless sintering process, the nano zirconia ceramic was produced, factors which can affecting the properties of nano zirconia sinter body such as moulding press and the sinter temperature are analyzed;(3)By the microtherm pressless sintering process, the nano copper added functional zirconia ceramic composite was produced, microscopic dimensionality and electric properties of such sinter body and the factors affecting such sinter body are analyzed;(4)By the self-invented "external albumen coating" technique the zirconia powder was successfully coated by carbon in the corresponding sinter body, which can help solve the traditional aggregation problem to some degree;(5)Based on analyze the characteristics in the nano powder sinter process, the "three-ball sinter model" was proposed, for the relationship between the relative density and porosity of sinter body, by mathematical fitting, such model was successfully verified.

本研究比较系统地研究了纳米氧化锆陶瓷的合成与成型机理，特别是讨论了纳米氧化锆陶瓷的稳定性，为防止纳米颗粒在外场作用下的团聚和长大提供了理论基础和实验数据，具体工作有以下几方面：(1)采用共沉淀法和共沉淀-凝胶法制备了纳米氧化锆粉体，并分析了pH值和稳定剂含量对粉体性能的影响；(2)采用新型无压烧结工艺制备了纳米氧化锆陶瓷，并分析了成型压力和烧结温度对烧结体性能的影响；(3)采用低温无压烧结工艺制备出添加纳米铜的功能性纳米氧化锆复合陶瓷，并分析了烧结体的微观尺度和电学性能的变化以及影响因素；(4)通过自创的&鸡蛋清外敷法&在真空镀膜台上对纳米氧化锆粉体进行包敷碳颗粒的表面处理，并采用真空烧结工艺制得相应烧结体，初步开始解决陶瓷烧结过程中团聚长大这一传统难题；(5)通过分析纳米颗粒在制备烧结体过程中的实际特点，提出了&三球烧结数学模型&，通过引入坯体相对密度和孔隙率的相对关系分析并通过自行编写的数学拟合软件，验证了这一数学模型。

Presses and compression moulds for:·Composites, GMT, SMC, BMC·Rubber, with/without vacuum chamber·Thermosetting products for ureic resin moulding

主要技术：SMC、GMT、RTM、热压缩技术、热成型技术、修边技术、切削技术、打孔技术、滚塑技术、玻璃增强塑料技术和碳纤维技术。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。