查询词典 mould

The sequence parting mechanism of length bolt,etc.is used for disparting the cavities and demoulding sequentially when the mould is opened.

产品体积不大，但外形比较复杂，如果不仔细分析可能会采用斜抽芯机构来进行分模，这样将加大模具的设计和制造难度。

The key design points, such as the disparting mould face, pouring system, exhausting, embedding part placement and inside skirt core, are put forward. The method of disparting block and the order of drawing core for the inside skirt core are mainly analyzed. The developing prospect of APG process for the epoxy resin is forecast.

在电器、绝缘材料、输配电行业中，正在以环氧树脂注射成型工艺代替环氧树脂浇注成型工艺。l环氧树脂APG工艺原理环氧树脂APG工艺是在专用的环氧树脂自动压力凝胶液压成套设备上，利用环氧树脂注射模加工部件的一项新工艺。

Excepting be used in nail polishing of the newly-born nail care industry,our electric nail drill also can be widely applied in different fields, such as grinding,polishing,enchasing and carving techniques of jewelry processiong,manufacturing of mechanical mould.

本公司生产的打磨机除应用于美甲行业，配上不同的磨头还可以广泛应用于首饰加工中的打磨、抛光、镶嵌；工艺品的雕刻、机械模具制造等领域。

In addition, the forming reasons of entrapping poles and prejudicial shrinkage existing in the TiAl based alloy valves poured in permanent mould during the centrifugal casting process have been discussed.

此外，针对金属型离心浇铸Ti-48Al-2Cr-2Nb 合金汽车排气阀内部的常见缺陷，探讨了离心力场下排气阀内部卷入性气孔和偏中心线缩松的产生机理。

The following results are obtained by physical and mathematical simulation.The pouring height of the tundish has a certain influence on the quantity of the slag involved in the mould with the same tundish structure and production conditions. The slag quantity reduces as the liquid level rises; when the fluid level is under of a critical height the confluence vortex will appear near the nozzle, which easily entraps the slag.

通过物理模拟和数学模拟，得出以下结论：(1)在相同中间包结构和生产条件下，中间包浇注液面高低对下渣量有一定影响，随着液面升高中间包下渣量降低；当中间包钢水液面低于一临界高度时，则会在水口附近形成汇流旋涡，容易造成卷渣。

Therefore, they should work in the enterprises of mould designing and fabricating, electric manufacturing and so on.

可在电子信息产品制造类企业，精密模具设计与制造企业工作。

In this paper, the relationship between component and melting point of fluorine free mould fluxes was studied by means of regressive orthogonal design.

论文利用二次正交回归的设计方法对无氟保护渣的成分与熔点的关系进行了研究。

I just finished up with glassing the bottom part o' the mould this morning.

我只是完成了与glassing底部的一部分， o '模具今天上午。

I left the mould alone again till tacky to let the fillets harden up so I could get to my main glassing.

我离开模具，仅再次到tacky ，让鱼片变硬了，所以我可以得到我的主要glassing 。

Cracks,goffers and other defects often occurred in large work-piece products by expansion mould due to the big tensile deformation.

在生产中大型制件胀形模，由于材料拉伸变形较大，往往导致制件开裂、起皱等问题。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48