查询词典 mould in the pit

When the mould is dried and solidified, aluminum solution of about 700 ℃ is poured into the mould according to the process of ZCAST technique,and the syphon casting is successfully made.

针对美国Z Corp公司生产的快速原型ZCAST粉末价格昂贵的问题，采用自配制的质量百分比为4∶6的400目石膏粉ZP102和200目氧化铝粉的混合粉末，以弯管为研究对象，使用快速成型机成功打印出其模具零件，烘干、固化处理后，按照ZCAST技术的工艺流程，浇注700℃左右的铝合金溶液，成功铸造出弯管。

Trichomonad and mould: The prostate below normal circumstance does not have trichomonad and mould inside fluid.

滴虫与霉菌：正常情况下前列腺液内无滴虫和霉菌。

Resin transfer molding mould was manufactured with bisphenol-A epoxide vinylester resin as matrix,poly as low shrinkage additive and glass fiber tricot as reinforcing material,according to the basic requirement of matrix resin of RTM mould.

根据树脂传递模塑模具对基体树脂的基本要求，选用双酚A环氧乙烯基酯树脂为基体，聚乙酸乙烯酯为低收缩添加剂，玻璃纤维经编织物为增强材料，并加入相应的助剂，制备了复合材料RTM模具。

In the virtual surgery system, the virtual scalpel could be manipulated on 3D liver mould with PHANTOM. The simulating effect was the same as the clinic operation for auxiliary partial orthotopic liver transplantation. Plane visualization of hepatic resection and intrahepatic vessel cutting was achieved by adjusting the transparency of the resection part. Life-like could be felt and power feeling could be touched during virtul operation. Conclusion ① The visualized liver mould reconstructed is 3D and verisimilar, and it is helpful to design reasonable scheme for liver transplantation.

在建立的虚拟手术系统的虚拟环境中，使用力反馈设备PHANTOM操纵"虚拟手术刀"模拟了辅助性部分原位肝移植的手术过程，其结果符合临床手术的效果；通过控制肝脏模型切除部分的透明度，使肝脏手术切割平面可视化以及肝脏内部管道手术切断平面可视化；手术模拟过程逼真，形象，且有"力"的感受。

Cool in g time dom in ates cycle time in thick-wall mould in g like preform mould in g.

他的目光敏锐，一眼就望穿了隐含在一些天真无邪的行为下的可鄙的动机。

Subucultures of this mould were made and experiments conducted with a view of ascertaining something of the properties of the bacteriolytic substance which had evidently been formed in the mould culture and which had diffused into the surrounding medium.

形成了这种霉菌的子培养，而且实验在这种发现溶菌性物质的观点指引下进行，那是有证据表明，这种物质是由培养的霉菌形成并释放到周围环境中。

This paper introduces the approach to calculating mould taper and its appropriate corresponding casting speed according to the contraction of molten steel in mould, which can establish much more specific calculation formulae and breviate former ones.

摘 要 文中提出了通过钢液在结晶器中的收缩量计算结晶器锥度及其较好配合拉速的方法。建立了更为明确的计算公式，简化了以往的经验公式。

The deciduate casting mould agent casting mould drawing of patterns agent adopt high grade material to compound but is accomplished, have volatilizing speed is quick , efficient, spread brush repetition usage many times , do not glue a model.

铸型脱模剂铸型脱模剂采用优质材料配制而成，具有挥发速度快、效率高，涂刷一次可重复使用多次，不粘模。

This paper analyzes the principle of the LP-LFC process,presents the physical and mathematical models of mould filling of the new process. The patterns including window-plate, ladders cluster, electromotor frame and exhausting manifolds are poured using LP-LFC process with AZ91D alloy, and the mould filling course is tracked with electrode touch point method. Based on above tests and experiments,the casting defects including short runs, cold laps, trapped gas,metal penetration, and so on, were investigated. The appearance characteristics,birth causes and influence factors of above defects are discussed in the article,diagrammatize modes of the defects forming is also given, and the measures of reducing or avoiding defects are put forward.

本论文分析了低压消失模铸造技术的工艺原理，建立了低压消失模铸造过程中金属液充型的物理和数学模型；在各种工艺条件下浇注了薄板窗体、阶梯模样簇、电机外壳和发动机排气管四个典型的模样和产品，用电极触点法记录了镁合金低压消失模铸造的充型过程；试验研究了镁合金低压消失模铸造中出现的浇不足、冷隔、气孔、粘砂等典型缺陷，分析了这些缺陷的形貌特征、形成原因及影响因素，给出了缺陷形成过程的图解模型，提出了减少和消除缺陷的工艺措施。

Traditionally it is through the exogenic power by the mould to realize curving formed craft. Because the cycle of mould design and manufacture is long, and the processing charge is high, so it is comparatively suitable for the mass production.

传统的弯曲成形工艺是在外力作用下借助于模具来实现的，由于模具的设计、制造周期长，加工费用高，较适用于大批量生产。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48