查询词典 motor-driven

Electric remote control device adjustment is used, General monlchamus tuhung seat mounted above the keybed-iron plate, covering a hard plastic, and a flexible plastic to prevent ink seepage, each iron plate is fitted with a front end, eccentric roller roller bearing rings on both sides of the plastic top tight in tuhung roll, bucket seat is fitted with a total of 30 to 32 of these eccentric roll, each of which the width of the eccentric roll and 30 ~ 32 mm, when servo motor signal receiving console by mechanical structure, change the eccentric roller and rollers of the gap, so that once the monlchamus tuhung-high ink, led, according to the extruded plastic clearance form different deposit, attachthemselves in tuhung roll, roll over the ink input ink this structure is characterized by correctly restrict each supply the location of the monlchamus region of adjustment on the nearby monlchamus area for inking, plastic affected by friction, easy-to-wear constantly, you need to change on a regular basis.

而电不静调度是用遥控安拆来举行的，凡是的不朱斗座底下拆有一排琴键式铁板，暗不天包围一张软塑料片，而塑料片具有不塑性，制止油不朱的渗漏，每块铁板的前端拆有一个公道辊，辊双方的支承环不兵塑料片底不松在不朱斗辊上，不朱斗座上共拆有30～32个公道辊，每个公道辊的宽度约为30～32mm，当伺服电机剥夺把持台的暗记后，堵住板滞布局，保持公道辊与不朱辊的间隙，因此当不朱斗辊不静弹时，不静员油不朱挤不抬塑料片，不梢据间隙巨细变成差别不朱层厚度，附着在不朱斗辊上，堵住传不朱辊不输出匀不朱机构，这栽布局的特不面是可以不差不天不拘每个不求不朱区的场所，制止一个不朱区的调度差附近不朱区不求不朱度爆发感化，塑料片受到不停摩擦，难磨损，需按期调换。

A bumper is a part of a motor vehicle.

保险杆是机动车辆的一部分。

We've published a feature today from Mark Bursa, who recently visited the Bangkok Motor Show.

我们双方今天刊登一篇来自马克布尔萨，曾多次赴曼谷汽车展。

A bus bar voltage dip during motor starting, shall not exceed 10%.

电动机起动时的母线电压降不得超过10%。

The focus is fast and much quieter than the Canon, which has a traditional motor that is very buzzy in comparison.

是马头的对焦迅速，而且远较佳能头安静，佳能35mm镜头使用传统的对焦马达，相比之下显得噪音较大。

This design is the main engine will take the step motor actuators provide an idle by-pass inlet channel.

本设计主要是将汽油机的带步进电机的怠速执行器提供一个旁通的进气通道。

"For medium and larger horsepower sizes, some manufacturers elect to offer by-pass jacketed motor designs."

对于大中型功率的电机，一些制造商选择提供旁路加套电机设计结构。

The main technical parameters of equipment The largest diameter rod into the Φ8mm Diameter round Φ1.20mm-Φ3.5mm The maximum speed cable 25m / s Cable drum diameter Φ450mm Road stretching up to 13 defective Chu-line maximum length of 9m Set-up specifications PND500, PND630 13 die final round adjustable model separate motor

设备主要技术参数最大进杆直径Φ8mm 出线直径Φ1.20mm-Φ3.5mm 最高拉线速度 25m/s 拉线鼓轮直径Φ450mm 最多拉伸道次品 13道储线器最大长度 9m 收线盘规格 PND500，PND630 最终出线模 13模可调。

The performance of the motor is calculated.

计算了电机的相关特性。

Take advantage of the high-speed calculation capability of DSP. Without any additional speed-measuring circuit,calculating the running speed.,then modulating PWM can be easily made to control the speed of the motor.

充分利用DSP高速的运算能力，在不需要另加测速电路的情况下，软件计算电机的在转速度，然后根据在转速度，调节PWM波的占空比，很方便实现电机的调速，达到电机无传感器的控制。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。