查询词典 motor-driven

Operate the right hand grip of valve block at "CLOSE" position, and then the hydraulic oil get to the opposite cavity of motor, drive the motor to move the cover at close position by chain.

8.3 将阀组中右侧手动换向阀的手柄置于&CLOSE&位置，此时，油压经过阀组到油马达的B腔，油马达旋转时带动链轮，通过链条拖动舱盖在舱口围面板上运动，最后将舱盖拖曳到舱盖关闭位置。

Operate the right hand grip of valve block at "OPEN" position, and then the hydraulic oil get to the cavity of motor, drive the motor to move the cover at complete open position by chain.

8.2 将阀组中右侧手动换向阀的手柄置于&OPEN&位置，此时，油压经过阀组到油马达的A腔，油马达旋转时带动链轮，通过链条拖动舱盖在舱口围面板上运动，最后将舱盖拖曳到舱盖收藏端。

The traditional refitted ignition products (for example, high-pressure cylinder line without diffraction, refittedly-complicated products that mix the spark plug and ignition power) are the primang products with no dynamic adjusted ability, which can't meet different requirements of motor under different conditions, thus impossibly causing the motor to be in the best condition.

传统点火改装产品（如：无内阻高压缸线、改装用火花塞及仿冒点火王动力复合仪等产品）均为无动态调节能力的初级改装产品，无法动态满足发动机在不同工况下的不同需求，因而无法使发动机持续工作在最佳状态。

The interharmonic sources in power system are analyzed,such as converter equipment,fluctuating load,ferro-resonance,synchronous regulator cascade and induction motor. Its harms are expounded,including waveform distortion,light flicker and influences on measuring instrument,motor and power factor.

分析了电力系统中各种间谐波源，包括变频装置、波动负荷、铁磁谐振、同步串级调速装置及感应电动机，阐述了间谐波的各种危害，如波形畸变、灯光闪烁及对测量仪表、电动机、功率因数的影响。

This article based on demand of production specially of that operator of production can master a little knowledge just to use it ,research theory of Artificial Intelligence , motor fault mechanism and fault forms Jooking for junction between Artificial and Motor Fault Diagnosis .

在此基础上，重点研究基于框架理论的专家系统在电机故障诊断中应用，及探索电机模糊诊断等，在人工智能在故障诊断作了一些探索，主要完成以下工作： 1。

Kai-kai Fu'an wind motor cover motor factory located in China Town - Fujian Fuan, the company was founded in 1990, is a competition in the market gradually moving towards standardization, modernization and the size of enterprises.

福安市凯佳电机风罩厂位于中国电机城-福建福安，公司成立于1990年，是一个在市场竞争中逐步走向正规化、现代化的规模企业。

Taxable products: motor cars, coaches, work vans, cross country vehicles and other small motorised passenger vehicles, trucks under 8 tonnes, motor cycles, video recorders, photocopiers, colour projection, television sets, television kinescopes, electronic calculators, microcomputers and peripherals in processed polyester thread and chemical fibre fabrics.

一、 征税品种为：小轿车、旅行车、工具车、越野车和其他机动小客车、八吨以下载重车、摩托车、录相机、复印机、彩色投影电视机、电视显像管、电子计算器、微型计算机及其外围设备、涤纶加工丝、化纤织物。

Screw on the choice of friction loss, high efficiency, high precision, long life of the ball screw, the electrical selected stepper motor, motor and the ball screw with gear deceleration.The main to modify the lathe is to modify the portrait, horizontal enter to the system in the Whole modification process and choose the automatic knife rest and be processed the thread need by pulser. The whole control system with the CPU of JKW-15T is to control the machine for center, through a plait distance drive tool machine an equipments to carry on control to attain need of process degree.

整个改造过程主要对车床纵、横向进给系统进行改造，丝杠选用摩擦损失小，效率高，精度高，寿命长的滚珠丝杠，电机选用步进电机，电动机与滚珠丝杠用齿轮减速；刀架改造成能自动换刀的回转刀架，由脉冲发生器来加工所需要的螺纹；整个控制系统以JKW-15T型号的单片机为中心，通过编程对机床的驱动设备进行控制以达到所需要的加工程度。

So the finite element method is applied to analyze the magnetic fields of the motor. And then some important parameters of the motor are calculated accurately, including flux leakage coefficient, computed pole embrace, and computed armature length and so on .

本文采用了场路结合的方法，首先利用磁路法对电机进行初步设计，然后建立有限元分析模型对电机的参数和性能进行精确分析，采用这样的方法不但可以满足精确性要求，同时可以缩短设计周期。

Based on the magnetic field calculation some parameters of the sample motor such aselectromotive force with no load, leakage coefficient with no load and magnetictorque are calculated and influence on the parameters that is caused by the change ofthe structure of the sample motor is also discussed.

在电磁场计算的基础上，进行了电机空载反电势，空载漏磁系数，电磁转矩等相关参数的计算，讨论了横向磁通永磁同步电动机的结构变化对参数的影响。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐