查询词典 motor-driven

The main objective of this design is the completion of the stepper motor control.

本设计的主要目标是完成步进电机的控制。

You will hear the compressor motor beginning to run.

你会听到压缩机电机开始运行。

This paper discusses the mechanisms and implementation details of concatenation control in a three - phase asynchronous motor with double closed loop.

本文所讨论的是双闭环三相异步电动机的串级调速的基本原理与实现方法。

Run smooth, safe and reliable: the motor shaft and pump shaft for coaxial Direct, high concentricity, run smooth, safe and reliable.

运行平稳，安全可靠：电机轴和水泵轴为同轴直联、同心度高，运行平稳，安全可靠。

Correction coupling centerline, the motor shaft and pump shaft to maintain concentricity.

校正联轴器的中心线，使电机轴与泵轴保持同心。

New concerns have arisen over the emissions from the growing number of motor vehicle.

但是由于汽车的增多，人们对汽车尾气的排放问题产生了新的忧虑。

Our products mainly include: Rivet nuts, Nylon insert lock nuts, Wing Nuts Series, Flange nuts Series, Weld Nuts Series, Locking nuts, Acorn nuts Series, Cone Nuts, Wheel Nuts Series, Hex Fin nuts Series, T-Nuts Series, Bulgy Nuts Series, Reflector Nuts Series , Square Nuts Series, Slotted Nuts Series, Special Nuts Series, Ball Head Of Motor Vehicles Windshield Wipers Series, Special Nuts Series,etc.

主要产品有：铆螺母、尼龙防松螺母、法兰螺母、蝶型螺母、焊接螺母、自锁螺母、盖形螺母、正非标螺母及罗拉、套管、汽车雨刮器球头等系列。

Secondly, it analyses the line type between stator and rotor of PDM, gets its derivation bone line equation that satisfies the motor conjugate line type of theoretical sealing and the equation of curved surface, and determines its basic processing method and technology according to the line type characteristic of the spiral curve through analyzing some kinds of typical spiral curve processing methods.

其次，对螺杆钻具定子与转子进行线型分析，推导出其满足理论密封性的马达共轭线型的骨线方程和曲面方程，根据螺杆钻具定子内孔螺旋曲线的线型特点，在分析了几种典型的加工螺旋曲线加工方法的基础上，确定了其基本的加工方法和工艺。

The system includes a gearbox (40) and first and second planetary gearset assemblies (42,44) connectable between an output shaft (36) of the motor and a drive shaft (38) of the pump.

该系统包括齿轮箱以及可连接在马达输出轴和泵的传动轴之间的第一和第二行星齿轮组组件。

The first process is to optimize the geometric parameters of the press, on the assumption that the servomotor rotates at a constant angular velocity equal to that of the constant velocity motor. The second process is to optimize the displacement trajectory of the servomotor based on the results of the first process while keeping the geometric parameter unchangeable.

然后，建立了混合驱动压力机的优化设计模型，并将优化分为两步：第一步，假定伺服电机角速度与常规电机相同的条件下，优化设计出压力机的尺寸参数；第二步，在第一步优化结果的基础上，使机构的尺寸参数不变，优化设计伺服输入运动规律。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。