查询词典 motor control

On the research of reciprocating pump,if the linear motor-driven piston or reciprocating plunger being applied,the structure of reciprocating pump will be greatly simplified.And the movement of the piston can be changed so that the flow of pump is constant;Meanwhile easily to achieve automatic control,and when using the intelligent control system,easily to implement automated production.

在往复泵的研究中，如果采用直线电机直接驱动做往复运动的活塞或柱塞，那么往复泵的结构将大为简化，泵总体结构紧凑，系统效率高；并且可以通过改变活塞的运动规律，使泵的流量恒定；同时便于实现自动化控制，若采用智能化控制系统易于实现自动化生产。

In doing so, I learned that by opening a small panel door just above the pump panel, you could gain access to the control valve and that removing a small pin from the Rate-of-Flow Control Valves point where the valve handle connected to the motor, you would then be able to operate the valve by hand.

这样做，我知道了打开水泵正上方面板的小面板门，你可以进入控制阀，并剔除了点小针在阀门手柄连接到汽车，你便可以为手工操作阀门。

Based on mathematical model, torque control and speed control methods of simulation of wind turbine based on DC motor are analyzed in detail. Then simulation model and experimental system are built to test and verify theoretical analysis.

以数学模型为基础，详细分析了直流电动机模拟风力机的转矩控制和转速控制方法，并通过建立仿真模型和实验系统对理论分析进行验证。

In order to achieve good dynamic performance for disturbance rejection, parameter vibration and set point tracking, an intelligent fuzzy self-tuning PI control is used to control the velocity for the piezoelectric ceramic motor.

因此，本论文针对压电陶瓷马达驱动系统参数变动或负载干扰影响，提出一智慧型模糊自调式比例积分控制架构，藉以改善传统比例积分控制的缺点，而得到较佳的系统暂态响应及负载干扰的消除。

The NC remaking scheme of tool grinder is a closed-loop control system, which uses single-chip microcomputer as a control system and step motor as the executive equipment.

以工具磨床刃磨铣刀螺旋刃的数控改造为例，阐述了基于单片机控制的数控改造方法。

In this paper RoboCup Mid-size Robot are the object of study from the two sides of the robot system and the system of multi-robot cooperation, the main research results are as follows: First, this paper reasearches the problom of the hardware and software architecture of Mid-size robots. According to the real-time requirements of the competition, the paper designs the mechanism of omni-direction wheels, which achieves a great improvement on the traditional mechanism of two wheels robot, and a more flexible response. This mechanism can adapt well to the increasingly rapid pace of the competition. In allusion to the mechanism of omni-direction wheels, this paper designs the electrical control system of three nodes in the bottom, which could communicate fast to the laptop with serial port and match the real-time requirements well. According to the problom of hitting power and speed of robot when shooting, this paper designes a motor-driven tongue-shaped spring shooting mechanism, which has a simple mechanical structure, smaller space in size and simple control circuit. This shooting mechanism meets the real-time requirements of the competition better.

本文以RoboCup中型机器人作为研究对象，分别从机器人自身系统和多机器人协作系统两个方面进行了研究，主要研究成果如下：首先，研究了中型机器人的软硬件体系结构问题，针对实时比赛的要求，提出了万向轮机构的设计方案，大大改进了传统两轮机器人结构，动作反应更加灵活，该机构能够很好的适应节奏越来越快的比赛；针对万向轮机构，设计了3节点的底层电机控制系统，它可以通过串口与上层笔记本电脑快速通讯，能够很好的实现实时工作要求；针对机器人射门时击球力量和速度的问题，设计了一套电机驱动的舌形弹簧射门机构，机械结构简单，占用空间体积小，控制电路简单，较好的满足了比赛中实时射门的要求。

This paper presents a simulation test control system of an airplane engine operating system, which control motor to simulate the force and velocity of throttle lever and the torque on axis.

本文阐述了某型飞机发动机操纵系统地面模拟试验控制系统，它主要控制力矩电机去模拟油门杆上的速度和力以及模拟发动机输入轴的力矩。

Tension control equipped with floating roller, 7-motor, 4-section tension closed-loop control system.

张力控制采用浮动辊式，七电机四段张力闭环控制系统。

Breakthroughs in the design of the traditional method of packing circuit design, use of one-way valve to control packing purposes, through the electronic control system in the fuel tank of hydraulic circuit in a closed state-pressure pump motor, through the valve to adjust the proportion of Circuit The pressure to ensure that Circuit in the changing pressure, not only to conserve energy and prevent the oil temperature rose too high.

设计时突破传统的保压回路设计方法，采用液控单向阀达到保压目的，即通过电控系统在油缸液压回路处于保压状态时关闭油泵电机，通过比例阀来调节油路中的压力要求，保证油路中不断变化的压力，不但节约能源，而且防止油温上升过高。

A deviation to enable business card printing and membership card making more neatly away material; business card printing and membership card Studio Center-drum for double-deck, using thermostatical hollow water circulation system structure, plated nickel plating avoids corrosion, Nano-imprint lithography drum machine, safe and reliable braking equipment; spam satellite business card printing and membership card, four business card printing and membership card production unit in the Centre of coining drum distribution around the business card printing and membership card making support adoption of the integral structure, intensity that cannot be easily; Center for the imprint drum version, roller roller, using separate servo motors between the gearless, Business card printing and membership card making length is not supported by gear pitch in roll-wide choice; business card printing and membership card making pressure, roller and roller pressure singlein servo motor and with memory with two types of regulation, accurate and rapid adjustment; closed ceramic Roller blade device ink to ensure that the business card printing and membership card making ink stability, blade-like device for pneumatic compression; taojian the plate cylinder, taojian-reseaus and roller, the portal structure of push-pull roller and taojian beckenbachannular roller to replace a simple and quick; roller servomotor-driven business card printing and membership card production and business card printing and membership card making machine be a certain speed, stopping the slow down to prevent the ink roller network hang dry knot, splash-proof ink installed equipment downtime or roller pressure, from the printing plate out of arrive﹖, stop to ink, the plate cylinder the full delivery from the pressure to keep the printing plate clean; stainless steel-monlchamus tuhung-glass to prevent ink prints get dirty; dryer direct to the wind, air flow loss small high efficiency, reduces noise scene, new oven heat energy to secondary structures, control temperature control system using intelligentized; traction roll at the same time acts as both a cooling rolls, new structure increases cooling effect.

纠偏，使制卡和会员卡制作走料更加整齐；制卡和会员卡制作部中心大滚筒为双层空心式，采用恒温水循环系统结构，表面镀镍处理可避免锈蚀，中心压印滚筒采用机械制动装置，安全可靠；卫星式制卡和会员卡制作方式，4个制卡和会员卡制作单元分布在中心压印滚筒周围，制卡和会员卡制作支架采用整体式结构，强度好不易变形；中心压印滚筒、版辊筒、网纹辊之间采用独立伺服电机无齿轮传动，制卡和会员卡制作长度不受齿轮节距限制，在版辊范围内任意选择；制卡和会员卡制作压力、网纹辊与版辊之间的压力分别用伺服电机调整，并具有记忆功能，调整有两种调节方式，精确调整与快速调节；陶瓷网纹辊封闭刮刀装置供墨，可确保制卡和会员卡制作过程中油墨稳定饱满，刮刀装置为气动加压；套筒式印版滚筒，套筒式网纹辊筒，门式推拉式结构使套筒版辊与套筒网纹辊更换简单快速；网纹辊由伺服电机驱动，制卡和会员卡制作时与制卡和会员卡制作机保持相对一定的速度，停机时则放慢速度匀墨，防止网纹辊网坑枯结，两边安装防油墨泼溅装置，在停机或离压时，网纹辊立即从印版脱离开来，停止给墨，印版滚筒把墨完全传递后离压，保持印版清洁；不锈钢接墨斗，防止油墨滴漏蹭脏印品；干燥箱采用直接进风型式，风量损失小效率高，减小了现场噪音，新型烘箱结构热能可二次利用，控制采用智能化恒温系统；牵引辊可同时兼作冷却辊使用，新型结构增大了冷却效果。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。