查询词典 motor control

First, the dissertation summarizes the properties, developing state and application fields of BLDCM, then its fundmental structure; operation principle and control strategy is also presented. On the base of roundly analyzing all kinds of the drive motor in electromotion type railway switch, BLDCM is proposed to replace the formerly traditional DC motor in railway switch. Second, the whole design scheme and key technology of control system is put forward based on analyse of the technical parameters and requirements.

首先，论文介绍了无刷直流电动机的特点、发展和应用概况，分析了稀土永磁无刷直流电机系统的基本构成、工作原理和控制方法；在对目前各种电动转辙机驱动电机分析的基础上，提出将稀土永磁无刷直流电机用于铁路转辙机，以替换原有的串励有刷直流电动机。

Based on the structure of vector control system for asynchronous electric motor using current model, the favorableness of vector control is validated by making reference of an actual electric motor and utilizing simulink simulation software.

根据使用电流模型的异步电动机矢量控制系统的结构框图，采用交-直-交间接变频器，以实际电机为例，利用simulink仿真软件，验证了矢量控制的有利性。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The presented diagnosis approach was validated by induction motor variable voltage and variable frequency control system as well as permanent magnet synchronous motor field-orientation vector control system.

为保障诊断的有效性和可靠性，提出采用开关信号上升沿延时的方法来避免因IGBT开通和关断延迟造成的误诊断，并给出延时时间的确定方法。

These are widely used in: micro-wave oven transformer, three-phase electric power, low-voltage control transformer, machine tool control transformer, neon light transformer, rectifier in lamps, electric soldering machine, washer double thermoelectricity machine, rectifier, wide screen color degaussing turn, kitchen electric machine, magnetic mine choosing facility, auto spare part, motor car spare parts, electric motor car, and wire and cable, fan jar, inverted power source, UPS power source, water pump electric machine, air-compress electric machine, disk wire, and so on.

公司的主营业务为漆包圆铝线，漆包圆铜线，铜包铝线和裸铝丝的制造和销售，主导产品为220级聚脂复合聚酰亚胺漆包圆铝线、铜包铝线和裸铝线等，广泛应用于：微波炉变压器、三相电力变压器、低压控制变压器、洗衣机双热电机、整流器、大屏幕彩电消磁线圈、厨房电机、磁矿选设备、汽车备件及电线电缆等。

A vector control method of linear induction motor based on fuzzy control was proposed because it was difficult to establish accurate mathematical model of linear induction motor.

直线感应电动机精确的动态数学模型很难建立，提出了一种基于模糊控制的直线感应电动机矢量控制方法。

In an induction motor maximum efficiency control system based on vector control, variation of mutual inductance resulted from the magnetizing flux adjustment is a problem to be solved. This paper proposed, based on model reference adaptive system, a novel method for on-line identification of the induction motor mutual inductance.

针对矢量控制下感应电机最大效率控制系统中由于调整磁链而引起的励磁互感变化问题，基于模型参考自适应(model reference adaptive system，MRAS)提出一种励磁互感在线辨识新方法。

Mechanical parts of the original target ordinary screw, the drive motor and control components of the transformation, the transformation of the system after a stepper motor, ball screws and other components, form a open-loop control system.

机械部分主要针对原普通丝杠、驱动元件和控制电机的改造，改造后的系统采用了步进电机，滚珠丝杠等元件，构成了一个开环控制系统。

This thesis make a study on Vector-contorl WVF system of asynchronous motor. In the course of study, making use of the mathematical model of asynchomous motor in MT axes. Then both open-loop control system and close-loop vector-control system are respectively simulated with simulation block SIMULINK in MATLAB.

本文对异步电动机变频调速系统进行了研究，利用异步电动机在二相同步旋转MT坐标系下的数学模型，使用MATLAB中的仿真工具箱SIMULINK分别对开环控制系统和闭环矢量控制变频调速系统进行了仿真。

Computer software use the VC++ 6.0 to develop a human-computer interface which can give a control order to the object, print and save the collected data in order to enquiry, deal with abnormal situations and so on. Computer hardware mainly complete the design of electrical control system, including motor-controlled, motor-driven, torque signal- acquisition and the design of interface circuit.

上位机软件采用VC++6.0进行设计，主要用它来开发一个人机交互界面，对试验台发出控制命令、可以打印采集到的扭矩数据并同时将数据进行保存以便查询、对异常情况进行处理；下位机硬件主要完成电气控制部分的设计，包括电机的控制、电机的驱动、扭矩信号的采集和接口电路的设计。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。