查询词典 molten metal bath

The four conditions are as follows: the molten alloy only with the addition of deoxidant during melting; only applying high-density pulse electric current on castings during solidification; compound addition of grain refiner and sodium modifier, and addition of borax r modifier liquid along with applying pulse electric current during melting.

这4种工艺条件分别为：在合金液熔炼过程中，除了加脱氧剂外不做任何处理；凝固过程中单独施加高密度电脉冲；添加晶粒细化剂和钠盐变质剂混合剂，或者添加硼砂变质细化剂，并施加高密度电脉冲。

This paper describes the new refining method and different factors influening dehydrogenation rate and deoxidation rate of molten steel.

本文主要研究各种因素对精炼钢水脱氢率、脱氧率的影响。

Produced silicon carbide composite Deoxidizer near ten series of products, including specifications, is based on carbon and silicon covalent bond mainly a combination of compounds, non-oxide material in the smelting converter part and the part of low carbon steel alloy the process of substitution of steel by carbon ferrosilicon and carried out on molten steel deoxidation and carbon use.

公司生产的复合型碳化硅脱氧剂系列产品包括近十个规格，是以碳和硅为共价键为主结合而成的化合物，属非氧化物原料在转炉冶炼普碳钢部分及部分低合金钢过程中替代硅铁和增碳剂对钢水进行脱氧和增碳使用。

This paper carried out the research on the dephosphorization and desul-phurization of molten steel systematically according to synthetic refining slags.

本文针对合成精炼渣对钢水脱硫、脱磷作用做了深入系统的研究。

Application of image processing system based on digital signal processor to temperature field measurement in laser molten pool .

基于数字信号处理器的图像处理系统在激光熔池温度场检测中的应用。

We eat it by dipping small pieces of bread in the molten cheese.

我们吃的时候将小片的面包蘸在里面吃。

The viscoelastic behavior expressed by the discrete linear relaxation spectrum is one of the most important properties for molten polymers.

粘弹性是熔融聚合物的一个重要特性，通常可以利用离散线性松弛谱来进行表征。

Magma, which is molten volcanic rock below the surface of the ground, heats the ground above it, keeping it green, The story goes that an early settler from Iceland gave Greenland its name in order to encourage more people to live there!

岩浆，就是地层表面底下的融化火山岩，为地面提供热量，使之保持翠绿。据说，有个早期来自冰岛的移民，为了鼓励更多人到格陵兰居住，所以将它命名为绿岛。

Carbon nanotubes were formed electrolytically in the LiCl melt with the diameters in the range of 75~100 nm, but β-Sn-filled carbon nanotubes were generated in molten LiCl+1.0%SnCl2 mixtures.

在 LiCl 熔盐中可得到直径为75~100 nm 的纳米碳管；在 LiCl+1.0 %SnCl2熔盐中可生成β-Sn 填充的纳米碳管。

In order to produce the billet without surface defect under high casting speed and to raise the ratio of DHR or HDCR operation and reduce defect ratio of the final products, soft contact EMCC (Electromagnetic Continuous Casting) technique by imposing high frequency electromagnetic field on the molten steel meniscus region has been developed. This technique is used to control the initial solidification of the billet.

为了在高拉速条件下生产出无表面缺陷的铸坯，以进一步增大铸坯HDR或DHCR的操作比率、提高最终产品的无缺陷率，连铸技术工作者开发出利用高频交变磁场对铸坯初始凝固过程进行控制的软接触电磁连铸技术。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。