查询词典 molten metal bath

To strengthen electrotype by pouring molten metal to its back. Also called Backing up.

2把熔化的金属，浇涛在电铸版的背面，以增加它的强度。

Kalium and natrium erode into brick at a high temperature in the form of simple substance and result in expansion in self-baking carbon brick, and molten alkali metal oxides adsorbed on the face of brick react with SiO2 and obtain a eutectic mixture which causes expansion at a high temperature, while carbon deposition caused by the reaction of CO and simple substance of kalium and natrium as well as the soot deposition of CO contribute to the lower temperature expansion.

结果表明：膨胀率及碱含量都随温度和时间的增加而增加，膨胀率受时间影响较大，达到8%左右，而受温度影响较小，仅为1%左右；砖内K， Na元素质量分数受时间和温度的影响均较大，分别达到4.5%，5.33%，4.28%，4.46%，且Na侵蚀较K严重；在高温下K， Na是以单质形式侵入砖体内，而熔融碱是吸附在砖体表面并与SiO2：生成低共熔化合物引起高温膨胀，在低温下砖内K，Na单质与CO发生C沉积以及CO发生烟碳沉积反应引起低温膨胀。

An alloy of ferromanganese is added to the molten metal as it is poured from the converter into the ladle.

是工具理性在教育中的具体化。10。人们在钢水轻炉倒进钢水桶时，放进一些锰铁合金。

Fettle:To line the hearth of with loose sand or ore in preparation for pouring molten metal.

涂：为倒入熔化的金属作准备而用松散的沙子或矿渣涂炉膛。

Qingdao°·French°·company to introduce a complete set of production technology and management experience, specializing in the kinds of non-standard heat pipe radiator (IGBT, GTO, diode, thyristor, optical devices, such as heating power devices used), water cooling plate, heat pipe heat exchanger (for closed, air / air), and the molten metal heat insulation direct immersion heater used for research and development and production.

青岛阿特姆全面引进法国阿特姆公司的全套生产技术和管理经验，专业从事各种非标热管散热器（IGBT、GTO、二极管、晶闸管、光学器件等发热功率器件用）、水冷却板、热管换热器（适用封闭箱体内，空气/空气）、以及熔融金属加热保温用直接浸入式加热器的研究和开发生产。

High melt surface stability could be obtained when molten metal level is located equally with upside of induction coil.

在电源频率一定的情况下，当金属液面与线圈上平面平齐时，液面波动平缓，在施加相同功率的交变电磁场条件下所得液面形状凸起越高，是电磁铸造所要求的液面状态。

It is proposed that the runner location should be first to be selected to ensure molten metal filling along the die wall in order to reduce melt flow resistance and then ingate should be located in the heavy section of the workpiece to which the melt would be filled at the beginning. As a result, the applied pressure could be transmitted fluently to avoid shrinkage cavity and to ensure castings quality.

指出浇道位置的选择首先要保证金属液沿着型壁顺序充填，以减少金属液的流动阻力；内浇道应使液态金属从制件厚壁处开始充填，以利压力的传递，消除缩孔，保证制件的质量。

When struck with a sharp edge, the Misch Metal flint produces small balls of molten particles that burn hotter and have a longer burn time than the sparks made by a standard fire flint.

当你用锋利的到划它的时候，这种复合金属火石产生一些炽热的小球颗粒，比普通打火石产生的火花温度更高，燃烧时间更长。

Surface'.'' of molten metal.

表面'。''形成的氧化物

Of'.'' molten metal.

的'。''氧化物

But this is impossible, as long as it is engaging in a market economy, there are risks in any operation.

但是，这是不可能的，只要是搞市场经济，是有风险的任何行动。

We're on the same wavelength.

我们是同道中人。