查询词典 mold

Heat transfer between ingot and mold is then intensified by the quickened flow velocity of Al melt. As a result, the initial solidifying point on the ingot surface in mold moves upwards to decrease the height of contact zone between the melt and mold so as to improve the surface quality of ingot.

铝熔体流动速度的加快能增强石墨环与铝熔体之间的换热，使结晶器内铸锭表面初始凝壳点位置上移，减小了铝熔体与结晶器的有效接触高度，提高了铸锭的表面质量。

The nil-ray tube spindles spinning plastic injection mold design, the key is to die with the ramp-pumping device and to accurately determine the direction of mold and mold guarantee Line is not in the external surface of the tubes.

该无合模线纺纱管锭塑料注塑模具设计的关键是该模具必须带有斜抽芯装置，并要准确确定合模方向，且保证合模线不能在管子的外表面。

Analyzed the structure characteristics of the perfume cover outer shell plastics piece, described the piece's structure and work principle which model a craft and inject a mold, its principle :adopt and certainly be apart from bolt and spring coil and carry on two cents type, use inclined lead a side outside the pillar and take out heart, type the heart crest spare parts, while entering and anticipating adoption incubate the type sprinkle into anticipate a form, while opening a mold, with the ball head pull and anticipate a pole sprinkle and note system and anticipate, then make use of and take out and push plank and release a plastics piece inside a heart,use spring coil and reset first while matching a mold, then carry on willing model a beginning next time.

摘要分析了香水盖外壳塑件的结构特点，叙述了该塑件成型工艺、注射模的结构和工作原理，其原理是：采用定距螺钉和弹簧进行二次分型，用斜导柱外侧抽芯，型芯顶出零件，进料时采用潜伏式浇口进料形式，当开模的时候，用球头拉料杆把浇注系统凝料顶出，然后利用型芯内抽推板推出塑件，合模时用弹簧先复位，然后进行下一次成型开始。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

Evaluation of particleboard made from rice straw bonded with NaOH modified SPI adhesive The effects of mold pressing temperature, mold pressing pressure, mold pressing time, initial moisture content of NaOH modified SPI adhesive coated rice straw, etc. on the mechanical properties of strawboard were investigated.

NaOH改性大豆分离蛋白胶粘剂对稻秸致密成型的影响研究研究NaOH改性大豆分离蛋白胶粘剂与切碎稻秸的模压温度、压力、模压时间、稻秸初始含水率等参数对稻秸成型板的物理特性和机械性能指标的影响。

Among them, a motorcycle tail lamp mold Maoming animation is in accordance with the College of Engineering, Institute of Electrical and Mechanical works of Yu-ling, in its Auto cad drawing of the schematic design produced, the mold is not only typical but also moderate level of difficulty, so as the most representative of the mold, to display animation tool.

其中，某摩托车尾灯罩的模具动画主要是依照茂名学院机电工程学院罗宇玲的作品，在其绘制的Auto cad的示意图上设计制作而成，该模具不仅典型而且难易适中，因此将其作为最具有代表性的模具，展示其模具动画。

Mold with baking soda as long as it is certainly not achieve bactericidal action, it is recommended to do in order leucorrhea conventional, because such a time, there may be changes, I found mold on 5 with a three-day drug, but also outside the washing soda , the situation improved, but also easy to check the recurrence of .6 months leucorrhea not conventional mold, but there is vaginal inflammation, washing lotion with medicine, and 7 months time to check card or a vaginitis, Trichomonas Streptomyces are is negative.

只要是霉菌用小苏打肯定起不到杀菌作用，建议再做依次白带常规，因为这么时间了，可能会有变化，我5个月查出霉菌，用了三天药，也包括小苏打外洗，情况好转，但也容易复发。6个月检查白带常规霉菌没有了，只是阴道还有炎症，用中药洗液洗的，7个月的时候去查阴道炎证也好了，霉菌滴虫都是阴性。

The Sacmi Group offers a comprehensive research and development service for the experimentation and composition of new mold resins."The sanitaryware industry is currently going through something of a transition period, with traditional low-pressure plaster mold casting steadily being replaced by high-pressure resin mold plants," said Vasco Mazzanti, technology and customer service manager of the company's Whiteware division.

由于目前的卫生洁具成型正处于一种由低压石膏模逐步向高压树脂模过渡的时期，Sacmi集团对新型树脂模的配方及实验进行了大量的研究与开发工作。

The Comprehensive professional basis, the professional course knowledge design "winding frame Injection Mold Design",its core of knowledge is plastic mold precision mechanical design, mechanical engineering materials, computer-aided design, mold CAD\CAM\CAE and so on.

综合运用专业基础、专业课知识设计《绕线架注射模具设计》，其核心知识是塑料成型模具、精密机械设计、机械工程材料、计算机辅助设计、模具CAD\CAM\CAE等。

Light guide plate molding technology is a optic dot transfer method by molding. Melt resin is injected into mold cavity, where optic dots are carved on to cavity surface. Then melt resin is transfered to LGP by keeping pressure, cooling and ejecting. Molding LGP have optic dots as same as optic dot design of mold stamper. LGP accidented optic dots are relative with mold optic dots.

导光板注塑成型技术是一种通过光学网点转移的方法成型导光板的技术，即将融熔树脂注入带光学网点的模具型腔，经过保压、冷却后脱模得到导光板，注塑成型得到的导光板具有模具型腔所赋予的光学网点，这些网点的凹凸性和模具型腔网点的凹凸性互补。

Hanna: That's over now, isn't it?

都结束了，对吗

You must be ill. You look so pale.

你一定是病了，你的脸色苍白。