查询词典 mold

The YY saccharomycetes was muted by diffent dosage heavy ion in the experiment, The data was analysied for obtaining the mold mushroom spawn lethality in 0.25~0.5GY, then through 3 steps screening, obtained the saccharomycetes which had grown well and beard the high consistence alcoho.

摘 要：本实验主要阐述了使用不同剂量的重离子对YY酵母菌进行辐照诱变选育耐酒精酵母的实验过程，结果表明：菌种致死率在0.25～0.5GY。

The water mold, Saprolegnia, which may be saprobes or parasites.

水霉，水霉属，为腐生或寄生种类。

I used saran wrap for mold release.

我用萨兰总结为模具释放。

In this paper, two assemblies of special test equipments have been designed and fabricated by authors in our laboratory: namely Catalyst Molding Process Analyzer and Catalyst Mechanical Process Tester. These new skills are developed for the dynamic studies on whole mold forming process and crushing process of Fe-Cr WGHS catalyst pellet. Based on the orthogonal experimental design, the effects of some factors during the forming process of solid catalyst, such as predensification proportion, calcination time, calcination temperature and content of graphite on the mechanical strength of catalyst pellets are systematically examined, and the molding conditions have been optimized. Based on the experimental data, the relationship between catalyst density and forming pressure are educed, and the physical significances of some related parameters are described. The parameter of macro scopic elastic moduls has been suggested to character the mechanical properties of molding catalyst. The effects of molding pressure on mechanical properties of catalyst pellets are discussed, and results show that there exists a optimal molding pressure for the ideal mechanical properties: when over-high or over-low pressure is applied, the specific surface area and side crushing strength of catalyst pellets will decreased. The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.

本研究通过自行设计制造的催化剂模压成型过程分析仪（Catalyst Molding Process Analyzer， CMPA）和催化剂力学性质测试仪（Catalyst Mechanical Properties Tester， CMPT），以Fe-Cr系高温变换催化剂片剂为研究对象，对成型过程和受压破碎过程提供了全过程动态研究的新手段；本研究利用正交实验设计方法考察了固体催化剂成型过程中诸因素（包含预密致比例、煅烧时间、煅烧温度和石墨含量等）对催化剂成型体强度的影响，并对成型条件进行了优化；根据实验结果，关联确定了固体催化剂成型过程中的密度－压力关系式，并对方程中诸因子的物理意义进行了描述；提出了一种利用宏观弹性模量来表征成型催化剂的力学性质的方法；研究讨论了成型压力对催化剂成型体强度性质的影响，结果表明：对于催化剂成型体的强度和比表面性质，成型压力存在着一个最佳值，过高的成型压力会导致比表面积和侧压强度的降低；不适当的成型压力的维持时间会破坏&压力回弹&作用，造成催化剂成型体的机械强度明显降低。

Serofluid will boil below, together with other condiments, pulp mold surface.

将浆水烧开下面，再配以其它佐料，即成浆水面。

In order to improve stress mode and dynamic stiffness of system, the compound frame of the punching and sheering units on multi-function bus press has been improved into the integrated framework, which makes mold clamping more convenient.

将原设备冲孔与剪切单元组合框架结构改进为一体式框架结构，从而改善了母线加工机的受力方式，提高了系统的动态刚度，模具装夹更方便。

3The opinions of workers toward treatment pattern--use the main values to mold teenage prostitutes in the sheltery organization, supervising the sequence in life is the focal point of treatment, treatment stays in superficial care for teenage prostitutes.

三、 工作人员对现行机构处遇型式的看法：包括以主流价值重新塑造被安置少女、生活秩序的管理成为处遇的重点、安置处遇停留浅层的照顾与陪伴。

Ltd. saved as much as 80% in mold change time after coordinating with Shih's team.

Ltd。公司在跟施博士的任务组合作以后，模具换型时间节省了80％。

In the construction of Guangdong highway, the slipform paver of SP1600 can t adapt to the actual production circumstance, it can t continuously pave the concrete surface of bridge, the tracks skiddy, the back mold pull the reinforcing bar and the horizontal beam with vibratory stick suffers interference etc.

针对WirtgenSP1600水泥混凝土滑模摊铺机不能连续摊铺桥面、履带打滑、后边模推拉钢筋网和振动棒横梁受干扰等问题，对相应的工作装置进行分析，通过技术、方案等研究，对WirtgenSP1600进行了技术改造，并在梅河高速路面5标项目中得到成功的运用。

This article is about Miner 's slamp slot cover mold design.

本文是关于矿灯槽盖的模具设计。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。