查询词典 modulus

Young Modulus of Kitan clay was measured during initial loading, after creep deformation, within small cyclic loading and global unloading-reloading.

Kitan粘土的杨氏模量分别在最初加载、蠕变后，小的周期加载和滞回圈时测定。

Main lambdoidal transmission gear of the great girder rolling mill is the key machine of this system.. It"s belongs to big modulus wide gear enduring heavy loads so it"s surface is easy to be hurt.

大型轨梁轧机主传动人字齿轮是轧机主传动系统的关键设备，该人字齿轮是大模数宽齿轮，承受载荷较大，易对齿面造成损伤。

It was proved that deformation modulus, compression strength, tensile strength, shear strength and Poisson ratio of lamprophyre could not meet the design requirements after high pressure cement grouting, so chemical grouting was proposed to treat the lamprophyre. High permeable epoxy resin was employed to grout the weathered lamprophyre.

因仅靠单纯的高压水泥灌浆无法使岩体的变形模量、抗压、抗拉、抗剪强度以及泊松比等物理力学指标达到设计要求，应有针对性地采用化学灌浆方法对煌斑岩脉进行加固处理。

Result The flexibility of the scaffold material was powerful. The load-elongation curve of the mechanical testing was similar to that of ACL, the maximum load, the ultimate stress and the Young's modulus of the scaffold materials were 52.61 N, 14.96 MPa and 202.08 MPa respectively. Human ACL cells displayed the representative characteristercs of the ligamentous fibroblasts, and synthesized extracellular matrix, such as type Ⅰand Ⅲ collagen protein. The scaffold materials had no cytotoxicity. Human ACL cells adhered, grew and proliferated well both on the surface and in the holes of the scaffold materials.

结果］韧带支架材料的柔韧性强，拉力测试的负荷－拉伸曲线与韧带的拉伸曲线相似，其最大负荷、极限应力和弹性模量分别为52.61N、14.96MPa和202.08MPa；体外分离培养的人前交叉韧带细胞呈典型的成纤维细胞特征，能在体外分泌Ⅰ、Ⅲ型胶原等细胞外基质；支架材料无细胞毒性，人前交叉韧带细胞可在支架材料上黏附、生长并分泌细胞外基质。

Adopting special lantern gear to minify the drive error of the screw drive chain on CA6140 lathe,high-precision inch-system lead screw and modulus lead screw can be processed.

采用专用挂轮，减小了CA6140螺纹传动链的传动误差，可加工出高精度英制丝杠和模数丝杠。

In this article, three kinds of prealloy powder were developed by water atomization method. The base attribute, pattern, phase composition, differential thermal analysis of powder were researched. Sintered density, hardness, bend strength, Young's modulus were researched as hot pressed sintering temperature changing. By using abrasive wearing equipment upbuilt by the authors, the wear resistance were determined. Green-pressing density, simulated green-pressing strength and bonding momental of high frequency brazing were assayed. SEM corrosion structure and SEM appearance of fracture were observed.

本文采用水雾化法开发了三种预合金代钴粉末：对粉末的基本属性、形貌，粉末的相组成，粉末的差热性进行了分析研究；测定了它们的烧结密度、硬度、抗弯强度、弹性模量随热压烧结温度变化的规律；采用作者自行建立的磨料磨损试验方法，测定了它们的质量磨损百分率；测定了它们的冷压生坯密度、模拟生坯强度以及高频钎焊的结合力矩；观察了热压烧结SEM腐蚀组织和SEM断口形貌。

The Constant Modulus Algorithm antenna arrays in the GSM systems are analyzed, CMA arrays can overcome the CCI from the intercells and partially overcome the ISI. The CMA is nonsensitive with the phase shift. The CMA criteria having real part and imaginary part can decreased the reliance of the sequentially temporal equalizer and carrier tracking measures

最后本文研究了CMA阵列天线在GSM移动通信系统中应用的可能性，CMA阵列可以有效地克服共道干扰CCI，部分克服码间干扰ISI，这样一种对相位不敏感的盲算法必须进行后处理，考虑复数的实部和虚部的CMA准则能够减少对后序处理的依赖程度。

B l ock model and its application in researching crystal cohesive energy and elas tic modulus are introduced.

介绍了分块模型及其在研究晶体结合能、弹性模量中的应用，对铜氧化物高温超导体结构和性能之间的关系作了探讨。

A wavelet modulus maximum denoising method is used to the denoising process of oscillographic chronopotentiometric signal.

将小波模极大值滤噪法用于处理含噪示波计时电位信号。

When the voltage space vector is located within overmodulation mode I, the locus in the hexagon remain the circular, but the amplitude is larger than the modulus of voltage space vector to compensate the voltage distortion on the edge of hexagon; the reference voltage vector tracks the hexagon sides in the remaining.

实验结果表明，该算法简单易实现，能够有效的提高直流母线的电压利用率，具有在低频运行稳定，逆变器输出电流正弦度好等优点。

He think the world care little whether a man is a churchman, so long as he is good and true.

他想只要一个人慈善忠厚，谁也不会介意他是否是个教徒。

Aiming at the temperature control requirement of multi-workplats fritting furnace, this paper presents an electric circuit design.

针对多工位扩散炉的温度控制要求，介绍了以TCA785为核心的可控硅移相触发电路设计。