查询词典 modulus

Based on the experiment, a finite element analysis model is established to predict the longitudinal shear modulus of X-cor sandwich structures.

在实验基础上，建立了X-cor夹层结构有限元分析模型，分析了Pin植入角、Pin直径以及Pin分布密度对X-cor夹层结构剪切模量的影响。

It was found that the membrane shear elastic modulus and membrane viscosity decreased in this process of changing. This finding may have some basic theoretical and clinical significance.

这对研究由于贫血等原因造成的网织红细胞增多情况下全血的微观流变学特性有重要的临床意义，同时对新生网织红细胞在转化过程中膜的剪切弹性模量和表面粘度的变化规律加以系统研究，具有重要的基础理论研究价值。

The prediction result of the in plane shear modulus of a typical stitching foam-core sandwich composite was found good agree with the experimental results.

预测典型缝纫泡沫芯材的面内剪切模量，进行夹层结构的面内剪切试验，试验结果与预估结果吻合较好。

The bender element system has been developed to characterize the maximum shearing modulus of soil mass, which provides a reliable and non-destructive method.

弯曲单元量测系统是一种实验室内用于无损检测土样最大剪切模量的土工试验手段。

Summarizing results show that study on the experiments and simulation of mechanical behaviors of carbon nanotubes is testing and simulating about its parameters, such as Young's modulus, shearing strength and tensile strength, the advantage...

综述结果表明：碳纳米管力学行为的试验与仿真研究主要表现在采用不同的试验方法与势函数对其弹性模量、抗剪强度、抗拉强度等参数进行测试与计算仿真，分析了这些方法用于研究碳纳米管力学行为的优缺点。

Interfacial shearing elastic modulus and interfacial shearing viscosity increased to 4.958mN/m and 3.9244mN ?

2三元复合驱采出液水相视粘度随着聚合物含量和相对分子质量的增加而增大。

RESULTS: The biomechanical parameters (maximum torsional momentque, torsion angle and shearing elastic modulus) of Wistar rat's femur irradiated with 15 and 20 kGy were almost the same with that of control group in torsion test.

结果：15，20 kGy辐照组与未辐照组扭转试验的生物力学测试最大转矩、扭角和剪切弹性模量结果相近，差异无显著性意义。

The results show that the amorphous PLGA fiber with porous structure (0.1-1.0 μm) is obtained by diluted solvent spinning method and the mechanical properties is affected by pressure and temperature. Bending strength and shearing strength of the samples increase firstly and then decrease with the increase of molding temperature and pressure. While the molding temperature is 160℃and the pressure is 105MPa, the PLGA materials possess optimal mechanical properties, bending strength, shearing strength and bending modulus 187.3 MPa, 100.0 MPa and 2.5 GPa, respectively. The mild temperature molding PLGA materials are desired to play a grate role in non-bearing internal fixation devices.

研究结果表明：非晶多孔结构的PLGA纤维可通过溶液沉析纺丝的方法获得，其孔径为0.1~1.0μm；压制压力和压制温度对材料的力学性能影响较大，材料的抗弯强度、剪切强度和抗弯模量均随着温度和压力的增大而先增大后降低；在压制压力为105MPa，压制温度为160℃时，试样的力学性能比较理想，此时，其抗弯强度可达到187.3MPa，剪切强度达到100.1MPa，抗弯模量达到2.5GPa，可望作为非承重部位骨折愈合内固定材料。

Received the asphalt mixture mechanics performance index with frequency through FSCH test, it point out that the complex shearing modulus: G*, G*/sind can appraise the high-temperature performance of different asphalt mixture well. But phase angle: d can't relatively produce quality of high-temperature performance of every asphalt mixture obviously.

通过FSCH试验得到不同频率下沥青混合料力学性能指标，指出复数剪切模量G*、G*/sinδ能较好地评价不同沥青混合料的高温性能，而相位角δ不能明显地比较出各沥青混合料高温性能的优劣。

Received the asphalt mixture mechanics performance index with frequency through FSCH test, it point out that the complex shearing modulus: G*, G*/sind can appraise the high-temperature performance of different asphalt mixture well. But phase angle: d cant relatively produce quality of high-temperature performance of every asphalt mixture obviously.

通过FSCH试验得到不同频率下沥青混合料力学性能指标，指出复数剪切模量G*、G*/sinδ能较好地评价不同沥青混合料的高温性能，而相位角δ不能明显地比较出各沥青混合料高温性能的优劣。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。