查询词典 modulus

Deformation modulus: the ratio of the vertical load to the vertical strain is called as Deformation modulus.

土的变形模量：土体在无侧向约束条件下，竖向应力与竖向应变的比值。

It is found that in certain water ratio and consolidation pressure, the values of initial elastic modulus and principal deviator stress increase with intermediate principal stress increasing; in certain intermediate principal stress, the values of initial elastic modulus and principal deviator stress increase with water ratio falling.

试验结果表明：在一定的含水率和固结压力下，偏差应力和初始切线模量均随中主应力比b的增大而增大；在中主应力比b确定的情况下，偏差应力和强度最大值随着含水率的增大而减小。

It is shown that both deviator stress and confining Stress greatly affect resilient modulus, and the influence of water content is great. Degree of compaction is also an important factor affecting resilient modulus.

结果表明：偏应力σ(下标d和侧向应力(σ3)对路基土回弹模量均有显著影响，含水量对路基土回弹模量的影响非常大，而压实度同样是一个主要影响因素。

Dynamic mechanical analysis,mechanical properties and the thermal dilatability measurements were used to study the effects of SF content on dynamic mechanical properties,impact strength,bending strength,bending modulus,specific strength,specific modulus,wear resistance and thermal dilatability.

采用动态力学、力学性能、热膨胀性能等测定研究了剑麻纤维的加入量对复合材料的动态力学性能、冲击强度、弯曲强度、弯曲模量、比强度、比模量、耐磨性能、热膨胀性能的影响，用扫描电镜观察了材料冲击断面和磨损面的形态。

The in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and its found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5%. The tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space.

研究结果表明：随着缝纫密度、缝纫线直径、最大纤维偏转角和缝纫变形区宽度的增加，缝纫复合材料层合板面内等效模量逐渐降低，最大降幅一般在5%左右；缝纫复合材料层合板的拉伸强度随缝纫针距的增加而增大，随缝纫行距的增加而降低，因此缝纫密度对拉伸强度的影响程度要看具体的缝纫针距和行距。

We employ ab initio plane-wave pseudopotential density functional theory to calculate the coordinate,the equilibrium lattice parameters,bulk modulus,shear modulus and elastic constant,and those calculated results agree well with the other experimental data and the theoretical data which have been published.

本文采用平面波赝势密度泛函理论方法计算了PtN2的坐标、平衡态的晶格常数、体模量、剪切模量和弹性常数，计算结果与已有的实验值和理论值吻合较好。

The experimental results showed that the elastic modulus and shear modulus decreased with the increasing of temperature in general.

实验还发现材料在结晶方向和垂直于结晶方向的弹性常数和蠕变特性等力学性质具有很大的差异。

It is indicated that the best ratio of external radius to inner radius relates not only to the yielding limit, elastic modulus and linear strengthening elastic modulus but also to Bauschinger effect factors.

公式表明最佳径比不仅与材料的屈服极限、弹性模量、线性强化弹性模量有关，还与鲍辛格效应系数有关。

As the carbon/ epoxy composites for the example, when fiber volume content and braid angle is fixedness, the influence of the 3-dimensional braided composites effective modulus that caused by thickness is more than by width, when width larger certain value and thickness larger certain value the modulus that composite is steady.

宽度变化对于E1 1影响较大，其他模量影响很小，当宽度大于一定值趋于稳定；而厚度的变化，对于复合材料不同弹性常数影响都很大，当厚度达到一定以后各个弹性常数的变化趋于稳定。

The main research contents and results are described as follows:The constitutive equation of the elastomer modeled by the fractional derivative Maxwell model has been investigated. Based on the thermodynamics constraints analysis of the physical parameters of the fractional derivative Maxwell model, the relaxation modulus and the creeping modulus of the model are analyzed.

本论文针对该目的，采用理论研究与试验研究相结合的方法，首先研究了胶泥缓冲器的耗能机理，进而设计开发了较理想的缓冲器产品，具体研究内容和成果如下：研究了胶泥的本构模型——分数微分Maxwell模型。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。