查询词典 mm.

Filter the cold solution using the Hirsch funnel (cover the bottom with a wet 17 mm filter paper) into a 50 ml filtering flask (don't forget to attach the neoprene filter adapter).

用赫氏漏斗(把一张湿的17 mm长的滤纸覆盖在它的底部)过滤冻的溶液，用一个50 ml的抽滤瓶接收(不要忘记要加一个由氯丁橡胶制的过滤接头)。

The initial point of collateral ligament was drilled two holes, 2 to 3 mm in distance, and crossed by steel wire. Then the superficial flexor tendon of finger was crossed under the steel wire and sutured to the terminal point of superficial flexor tendon of finger by 5/0 to 7/0 nontraumatic suture thread to maintain suitable tension, and sutured to collateral ligament by 8/0 nontraumatic suture thread.

用细克氏针在侧副韧带起点处向健侧钻两个相距2～3 mm骨孔穿过钢丝，切开屈肌腱鞘，从指浅屈肌腱一侧近端切取所需长度肌腱束，此肌腱束穿过钢丝孔，保持肌腱束的合适张力，用5/0～7/0无创线缝合于浅腱止点，应用8/0针线将肌腱束缝合于韧带上。

However, a third or fifth plugging was performed for 3 cases with 3-5 mm orificium fistulae.

而瘘口介于3~5 mm的3例患者注射次数分别为3次和5次。

The injection time was correlated to the size of orificium fistulae, and the plugging was successful for 4 patients with less than 3 mm orificium fistulae.

注射次数以及住院时间与瘘口大小有一定的联系，瘘口小于3 mm的4例患者均一次封堵成功。

Equipment 40 mm (1-1/2 in.) Flanged Equipment As recommended by equipment manufacturer

设备 40 mm (1-1/2 in。)法兰设备，根据设备制造商的推荐。

Control valves sized 4 100 mm and below shall have a minimum of 300# flanges.

100 mm及以下的调节阀应配最小是300#的法兰。

The results showed that dynamic cutting force F varied much compared with dynamic cutting force F and F. Dynamic cutting force increased with feed and depth of cut, especially when depth of cut was 0.1 mm.

动态切削力随进给量和切削深度的增加而增加，其中在切削深度为0.1 mm的情况下，切削力出现了较大的波动。

This article has mainly studied one kind improved two person two-sided synchronized GTAW craft for the austenite stainless steel. This craft makes the improvement in the original two person two-sided synchronized GTAW craft foundation which one time welding two-sides formings. A series of welding engineer testing on 8 mm SUS304 were carried on. The new craft could guarantee the welding quality in contrast with the original two person two-sided synchronized GTAW.

主要研究了一种改进了的奥氏体不锈钢的双人双面同步钨极氩弧焊工艺，此工艺是在原有的双人双面同步钨极氩弧焊工艺的基础上进行的改进，即将原有的一次焊双面成形改为两次焊成型，并在厚度为8 mm SUS304上进行了一系列焊接工艺试验，验证了这项新工艺与常规双人TIG双面焊相比，能保证焊接质量。

The friction and wear test was carried out on a MM-200 model test machine.

摩擦磨损试验在MM—200摩擦磨损试验机上进行。

The experimental investigation was carried out in a full baffled, flat bottom, cylindrical vessel, with 476 mm diameter, equipped with a new type propeller to push the water downward.

实验在直径为476 mm的平底搅拌槽内进行，全挡板条件，搅拌桨为CBYⅢ型轴流桨，下压式操作。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。