查询词典 mm.

A bulk metallic glass cylinder of Fe60Co8Zr10Mo5W2B15 with a diameter of 1.5 mm was prepared by copper mould casting industrial raw materials.

采用工业材料利用铜模浇注方法制备了直径为1.5 mm的Fe60Co8Zr10Mo5W2B15块状非晶合金。

METHODS: A circular cylinder-shaped whole-wall defect (6 mm diameter, 10 cm height) was made at 0.5 cm above femoral medial condyle.

于股骨内髁上段0.5 cm处制造直径6 mm，高为10 cm的圆柱状全壁缺损。

This completely new rotor head include leading edge blade control, 8mm blade holder spindle, 8 x 16 mm thrust bearings,, 5mm main blade drag bolt, and 3D inspired new design head damper rubber.

此全新的主旋头包括最尖端的主翼控制， 8mm 主旋翼螺母， 8 x 16 mm 压力轴承，5mm 拖螺栓，和新设计的3D橡胶缓冲垫圈。

Where it is fitted within a height of 450 mm above the car deck and exhaust ventilation trunking, electrical equipment is to be of certified safe type.

例 2：在离车辆甲板450 mm 的高度内及在排气通风导管内，可安装合格防爆电气设备。

The uncertainty evaluation of measuring results about indicator error of digital dial gauge 0~25 mm was analyzed in this article,those indicated that it was feasible using TWIN-CHECK1200 length measuring machine as calibration tools.

介绍了0~25 mm 数显千分表的示值误差测量结果的不确定度分析，表明了用TWIN-CHECK1200测长机进行校准的可行性。

Direct-acting pressure reducing valve diameter less than 20 ~ 25 mm, the output pressure of 0 ~ 1.0 MPa within the most appropriate, beyond this range should be used Pilot.

直动式减压阀通径小于20～25 mm，输出压力在0～1.0 MPa范围内最为适当，超出这个范围应选用先导式。

In view of DN 1600 mm Multi chamber drying tower, its drying mechanism, structure design, parameter calculation, operation effect, problems and some measures are discussed, also the choice of the matched equipment is made.

介绍DN 1600 mm多膛干燥塔的干燥原理，结构设计，参数计算，使用效果，存在问题及改进措施，并对配套设备进行选型。

Results showed that the flame-retardant performance of the coating was the best and the limit of endurance heat could get to 210 minutes when the content of the resin was 28 percent and the thickness of caoting reached 1.90 mm.

实验结果表明，当树脂基体的质量分数为28%，涂层厚度为1.90 mm的条件下，涂料的防火性能最好，耐燃时间超过210 min。

The presence of austenite at any 10% would causeloss of strength of both steels about 10 kg/mm~2, however, their toughness mightbe actually improved by these softer austenites formed along the boundaries oflath martensite.

回火奥氏体的存在使强度下降，估计10％的奥氏体使强度损失约10kg/mm~2。但较软的回火奥氏体沿板条状马氏体边界形成改善钢的韧性，使冲击韧性a_K提高。

The insulation batts shall be approximately 89 mm (3.5 in) thick and Rsi 1.4 – Rsi 1.9 (R8 – R11), positioned directly in contact with the outlet box and slit to completely surround the flexible metal conduit.

测试天花板器具应装两层表面有覆盖或没覆盖的玻纤绝缘棉，彼此成90度，绝缘棉的厚度大约为89 mm (3.5 in)，电阻为Rsi 1.4 – Rsi 1.9 (R8 – R11)，直接与出线盒相接触，并将柔软性金属导线管缠好。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。