查询词典 milling

The processing principle and method of slotting gear--grooves for big modulus gear wheel with combined milling cutter on a large--scale hobbing machine was put forward in the paper.

提出了在大型滚齿机上。用片铣刀组粗切大模数齿轮齿槽的原理及其工艺。使大模数齿轮的加工效率提高1～2倍。为大模数齿轮的高效加工开创出一条新的途径

In order to solve these problems, causes the processing process automation, tries to design one special-purpose numerically-controlled machine tool -- numerical control gear cutter, uses in key piece tooth which the milling locks, locks the factory satisfiedly the production need.

为了解决这些问题，使加工过程自动化，试设计一种专用的数控机床——数控铣齿机，用于铣削锁的钥匙片齿，以满足锁厂的生产需要。

A cutting tooth equipment is added in on general NC milling machine, machined screw bevel wheel is linked to dividing head, gearwheel is install on chuck, then, NC machining of screw bevel wheel can be realized with sequential evolutional method.

在普通数控铣上增加一铣齿装置，把被加工螺旋锥齿轮与分度头相连，大齿轮直接装在卡盘上，采用连续展成法实现其加工。

In the milling process, the water quality of Guilin, a very important role to play, practice has proved that only the Guilin area of this water, in order to make a long and continued good Gluten flour, if using the same technology to other places production, are difficult to be effective, it is a must.

在制粉过程中，桂林的水质起着很大的作用，实践证明，只有桂林这片地域中的水，才能做出长而不断，筋力上好的米粉，如果用同样的工艺到其它地方去制作，则难于奏效，简直是绝了。

The company is manufacturing the goal line milling, grinding, planing, boring machine business.

本公司是专业制造龙门系列铣、磨、刨、镗床的企业。

Advanced milling technology, strict manufacturing processes, and improve after-sales service staff are factory my eternal pursuit of the goal line.

先进的制粉工艺、严格的制造工序、完善的售后服务是我厂全体员工一致追求的永恒目标。

If not, the bearings will be worn and the life will be shortened, The methods of maintenance are as follows: oiling once for each shift. It should be noticed that the oil channel must be cleaned immediately if the oil is not be consumed or the loss is slow then 50# motor oil should be added. The oil cup is placed on the upper end of principal axis. Each shift should add 3# lithium base grease once with grease gun on bearing of principal axis base and bearing of milling roller. Disconnect and clean the analyzer once for 6 months and apply 3# lithium base grease. Apply lithium base grease for bearing room.(see lubrication system for details).

保养方法如下：主轴加油时间每班一次，但必须注意，发现油杯的油没有损耗或损耗太慢时，应立即清洗油道，再加50#机械油，油杯位置在主轴上端，主轴底座轴承，磨辊轴轴承每一班用黄油枪加注3#锂基润滑脂一次，分析器轴承每六个月拆开清洗一次，加足3#锂基润滑油，风机轴承室加锂基润滑脂。

It is a major Great Lakes port of entry and an important manufacturing and milling center.

是一个主要的大湖区进湖港和主要的制造业及''。

Annual production capacity of 50 Units grinder, milling machine 1000 Units.

年生产能力为磨床50台，铣床1000台。

Current equipment CNC machining centers, one Taiwan, 12 milling machines, lathes and grinders all three.

目前设备CNC加工中心一台，铣床12台，车床和磨床各3台。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48