查询词典 mid-century

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature.Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But ,it maybe flow if screw back pressure too high .

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，半夜盗汗897就去播播Z如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Besides, two representative temperatures, i.e. integral average temperature and mid-point temperature on cylindrical surface, are also calculated and discussed.

同时，对有限长面热源模型中的两种代表性温度，即热源面的积分平均温度和圆柱面中点温度分别进行了计算和讨论。

Since the mid-1990s, the nascent democratic transformation in Russia has given way to what may best be described as a \"czarist\" political system, in which all important decisions are taken by one man and his powerful coterie.

从90年代中期开始，俄罗斯的民主化进程便消失在了摇篮中，取而代之的是一种可称为"新沙皇主义"的政治制度，所有的重要事务都由最高领导人及其身边的强势内阁决定。

Czechoslovakian Army was equipped with some 249 ST-1 in 1949 and used them until mid/late 1950s.

捷克斯洛伐克陆军从1949年起一共接受了249辆ST-I并一直使用到了1950年。

This paper makes the range of integral mid-value point in Rn narrowed from integral region D to the inside of D/D .

将Rn中积分中值定理的中值点取值范围，由积分区域 D上缩小到D的内部D/D上取到。

Since the beginning of production in 2004 and until mid 2006 a total of 254,757 Dacia Logans were sold.

生产 自2004年开始生产，直到2006年年中的254757达契亚罗根轿车共售出。

Cyclists often come to Anna Saltonstall, a physical therapist at Mid-Columbia Medical Center in The Dalles, Oregon, with hamstring strains that could have been prevented.

Meghan Loftus 骑自行车者经常来到安娜Saltonstall，一位理疗师在Dalles的中间哥伦比亚医疗中心，俄勒冈，有可能被防止了的腿筋张力的。

Based on the investigation of four permanent plots, which are set in the mid-mountain of Darning Mountain and are in different recovery periods, the community dynamics during the vegetation restoration are studied.

本文对设立在大明山中山区处于不同恢复阶段的四个固定样地进行定位调查，主要对其植被恢复过程中群落动态学进行了研究。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。