查询词典 metal

After the metal liquid flowed alone the batcher drip nozzle, the fluxion was calm and chopping. The dimension of metal grains is even and the stability of production is very good.

金属液流经定量器滴嘴后，能够实现平稳、断续流动，加工的金属颗粒尺寸均匀、稳定性好。

The results showed that the composite batcher drip nozzle consisting of ceramics drip nozzle and plug had high strength, excellent toughness, abrasion resistance and corrosion resistance, and long service life. It was not easy to fracture while replacing. The new batcher drip nozzle could increase the productivity of production line and decrease the production cost of metal grains when it was used to cast metal grains.

结果表明，由烧结陶瓷加工而成的滴嘴本体及与滴嘴本体配合的塞子两部分构成的组合式定量器滴嘴，强度高，韧性、耐磨性和耐蚀性好，使用寿命长，更换时不断裂，可提高铸造金属颗粒生产线的作业率，降低金属颗粒加工成本。

Many batcher drip nozzles are installed at the bottom of holding furnace. The molten metal drips to the cooling water box which is mounted under the holding furnace through the batcher drip nozzle. The dwell time of granulated metal is 10~18 seconds in the cooling water box.

在保温炉底部，安装多个定量器滴嘴，保温炉内的金属液流经定量器滴嘴后，滴入保温炉下方的冷却箱内，金属颗粒在冷却水中停留10~18s。

For example, the quality of surface finish, amount of bearing clearance, metal carbon content, and type of metal processingmay influence the wear behavior of the bearing.

例如，表面抛光的质量，轴承间隙数值，金属与碳的比例，并金属制作的方法可影响负荷下的耐磨性能。

Later, pieces of metal, bearing values according to the rarity of the metal and the size of the pieces, or coins were used.

后来， 人们开始使用金属块或硬币，金属块上标有根据该金属的稀有程度和该金属块的大小而定的它的价值。

Metal ring in order to not beat in the vertical direction, the control cylinder bearing metal ring between the two sliding bearings.

为了使金属环不至于在竖直方向上跳动，用气缸控制轴承使金属密封圈在两轴承之间滑动。

While the ribbon is in direct contact with the metal bearing piece, current is passed between the electrode and the metal bearing component.

当条带与金属轴承件直接接触时，电流通过电极和金属轴承件之间。

Standard joint endoprostheses include metal components that are affixed to the articulating ends of the bones of the joint and commonly include a bearing component positioned between the metal components.

标准关节端部假体包括固定在关节骨骼的关节端部上的金属部件，并且通常包括定位在金属部件之间的承载部件。

Add ball bearing metal tail grips with metal pitch slider and pitch plate, and you have a solid tail for maximized gyro hold.

含有球头轴承的全金属尾旋翼夹头，结合全金属螺距调节杆和调节块的设计可保证机子拥有一个坚固的尾部联动装置，从而使陀螺仪的作用发挥到最大程度。

The circle shear machine 1 comprises a pair of center shafts, including an upper center shaft 20 and a lower center shaft 30, each having thrust bearing mounted sheet metal support members 25, and 35, respectively, which, when brought face together, engage on a top and bottom surface of a sheet metal blank 10, which is positioned therebetween.

The圆盘剪机器1包括一个对中轴，包括上部中轴20和一个更低的中轴有30，中的每一推力轴承登上的金属板支持成员25，和35，分别，当被带来的面孔一起，在上面时允诺，并且金属板空白10，底面被安置therebetween。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。