查询词典 meshing

After the interval was adjusted twice, the stress of the dangerous dedendum surface decreases 29% compared with the traditional meshing scheme of sabot, and the stress of every dedendum surface tends to be close, so this technology makes full use of the intensity of the composite.

通过2次间隙调整后，弹托危险齿根面的等效应力值相比传统啮合方式的应力值减少了29%以上，各齿根面的应力趋于接近，使复合材料的强度得以充分发挥。

Roller sprockets have some special dentiform teeth.Depending upon the meshing which lies in between chain teeth and chain nodes,it can transfer the desired movement.

滚子链轮上制有特殊齿形的齿，依靠链轮轮齿与链节的啮合来传递运动和动力。

To enhance the bearing capacity of NGW gear drive, the optimal design has carried on the outside meshing gear drive dislodgement parameter.

为了提高NGW型行齿轮传动的承载能力，对外啮合齿轮传动变位参数进行了优化设计。

It is an important but difficult job to compute the transmission ratio and the meshing efficiency of epicyclic gear trains.

周转轮系传动比与啮合效率(只考虑轮齿啮合摩擦损失)的计算方法卜3 J较多，但都比较沉繁。

Using two-flank-staining method, inspect the tooth flanks of the driven bevel gear, 3 to 4 equispaced spots along the circumference, at each spot apply color to 2 to 3 teeth, the correct meshing print requirements are: print width in the direction of face width not less than 50% to 60% of the facewidth , and that in the direction of tooth depth not less than 40% to 50% of the tooth depth.

用两面着色法，在从动锥齿轮的齿面检查，沿圆周均布3-4处，每处2-3齿涂色，正确啮合印迹要求为：在齿宽方向的印痕宽度不小于齿宽的50%---60%，在齿高方向的印痕宽度不小于齿高的40%---50%。

At first, based on the basic profile of the horological gear, the main meshing course is analyzed to determine the original parameters and the basic parameters.

本文的研究旨在提出理想的修形曲线对齿轮进行修形以达到提高啮合效率的效果。

Horological gear; meshing efficiency; profile optimization; approaching algorithm

中文关键词钟表齿轮；啮合效率；齿形优化；逼近算法

In the process of optimization design using ANSYS, the Optimized circulation may be intermitted because of some problems in modeling, Meshing, selecting design variables, state variables and objective functions, and optimized method.

引言应用工程优化设计软件进行结构分析[1～2]和优化设计[1，3]，可大大提高结构设计人员的工作效率，减轻结构设计人员的工作强度，是结构设计人员应具备的一项基本技术。

In the process of optimization design using ANSYS, the Optimized circulation may be intermitted because of some problems in modeling, Meshing, selecting design variables, state variables and objective functions, and optimized method.

应用ANSYS软件进行优化设计过程中，从几何建模、网格剖分到选择设计变量、状态变量、目标函数和优化算法，都可能会出现问题甚至导致循环中断。

The closed picture of involuted gear can not be applied to that of the point-line meshing gear.

封闭图主要确定大齿轮变位系数x2与螺旋角β，这样就相应地确定了其他参数。

Liapunov—Schmidt method is one of the most important method in the bifurcation theory.

Liapunov—Schmidt方法是分叉理论的最重要方法之一。

Be courteous -- even when people are most discourteous to you .

要有礼貌──即使当別人对你最不礼貌的时候。