查询词典 measuring error

At the same time, ambient temperature changes affect the acceleration of the method There is a certain measurement error, but the error of law stronger, from the basic structure, measuring principle, numerical and other aspects of the process of measuring the inclination and measurement system The structure of error correction for analysis.

同时，由于环境温度变化时对加速度计的影响，该方法存在一定的测量误差，但误差分布规律性较强，因此从基本结构、测量原理、数值计算等方面对倾斜度测量的过程和测量系统结构误差的校正进行分析。

Methods The effects of the reading error and the misalignment of the probes on the accuracy of measuring and all the harmonics of roundness were analyzed; The strategy and the algorithm for optimizing the parameters of the measuring system were proposed; The distribution and propagation patterns of the measured errors for all the harmonics of roundness were studied in detail; A software for correcting the errors caused by the measurement error of the angle positions of the probes and the sensitivity difference between three probes was presented.

分析了测头读数及角位置误差对圆度各次谐波及圆周各点测量精度的影响；提出了三点法测量系统的优化策略与算法；研究了三点法测量误差的分布与传递规律；提出了克服测头定位误差以及3个测头的灵敏度不一致影响的软件校正方法。

Usually, we assume that exterior ballisticmeasuring error has normal distribution with zero mean. But during the real measuring,it is possible for exterior ballistic measuring parameters to cause system error.

通常假定外测误差服从零均值正态分布，而在实际测量中，外测参数有可能带有系统误差，它的存在对飞行轨道和落点信息的获取都具有不利的影响。

The basic idea Is: using the standard value inserting the dynamic measuring errors which involve systematical errors and random errors, constructing the original error model which is revised at the same time and follows the variable law of the dynamic measuring errors, establishing a more suitable error model.

基本思想是：利用标准量插入动态测量数据实时分离含有系统误差和随机误差的动态测量误差值，建立误差的初始数学模型，并根据不断获得的标准点处的测量误差，实时修正或校正所建的初始误差模型，使误差模型不断跟踪动态测量误差的变化规律，建立更加符合动态测量过程的误差模型。

Compared with the conventional 2-D coordinate measuring systems, the new system has great improvement at measuring speed, aiming accuracy, measuring function and degree of automation The new system consists of two parts image measuring system of displacement and image autofocusing and aiming system The displacement measuring system in which CCD camera is used for locating the optical scale not only processes the advantages of absolute code measuring system powerful noiseproof feature, good long-time stability, easily compensated ruling error of optical scale, but also has the advantages of morden numerical systems easy numeralization and intelligence The autofocusing and aiming system in which CCD camera is applied for gaining the defocusing information and edge location information of workpiece enjoys the advantages of fast autofocusing, accurate result, high accuracy of edge detection and wide range of measured parameters, etc The feasibility of the new 2-D measuring system is analyzed in this thesis and related parameters are calculated.

详细本文在分析了现有二维中小尺寸测量系统中，光学仪器的光学读数系统和调焦、瞄准系统的优缺点之后，结合现代数字化仪器的优缺点，提出研制一种新的二维图像测量机系统。与传统二维坐标测量系统相比，新型系统在测量速度、瞄准精度、测量功能及自动化程度等方面都有较大的提高。该系统由图像式位移测量系统和图像式自动调焦、瞄准系统组成。图像式位移测量系统采用CCD摄象机拾取光学线纹尺的位置信息，既具有传统光学式绝对码位移测量系统的优点—抗干扰能力强、长期稳定性好、光学标尺误差易于补偿等优点，又具有现代化数字仪器易于微机化、智能化的优点。

A measuring system which mainly consists of a high precision motorized translation stage of one dimension, POINT GREY Flea2-14S3 CCD camera and LED light source was designed and constructed. Based on a detailed analysis for experiment results, the periodic changing law of system error of LED facula centroid location in this measuring system was found. The results indicate that based on Flea2-14S3 CCD camera, the random error of facula centroid location is about 0.018 pixels, the system error is about 0.06 pixels, and the total error is about 0.063 pixels (1/15 pixels).

利用高精度一维电动平移台、POINT GREY Flea2-14S3 CCD 相机和LED 光源构建了测试系统，对测试结果进行研究和讨论，发现了测试系统LED 光斑质心定位系统误差的周期性变化规律，计算得到了基于Flea2-14S3 CCD 相机的光斑质心定位随机误差为0.018 pixels，系统误差为0.06 pixels，总体误差为0.063 pixels(约1/15 pixels)，能够应用于以光斑质心检测为手段的测量系统中。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

In this paper, some characteristic functions of the multifunctional single-flank mesh gear tester of model CD320G-D which is applying gear integrated error measuring technique, computer technique, error separation technique, fault diagnosis technique and error prediction technique, including automatic searching of profile error start point, determination of profile barrelling, separation of profile form error and profile slope error, measurement of profile error with evaluation range subtracting tooth tip, measurement of tooth topograph and statistical analysis of gear manufacture error, are presented.

阐述了综合应用齿轮整体误差测量技术、计算机技术、误差分离技术、故障诊断技术和误差预报技术的多功能 CD320G-D 型单啮仪的一些具有特色的功能。这些功能包括齿形误差起测点的自动找定、凸形齿凸形量的测定及其形状误差与倾斜误差的分离、取值范围扣除齿顶部的齿形误差的测量、齿面轮廓度误差的测量以及齿轮加工误差的大样本统计分析。

This paper has described the basic function and qualification of the compensating brake master cylinder admeasuring apparatus firstly, given an introduction of gross structure, measuring principle and method, put its emphasis on the dissertation of working principle of main composing parts, such as endoscopic-micro optical system, CCD pick up camera and precision machinery system, and on the design of optical imaging system. It has analyzed the main error and the influence on measuring accuracy as well as giving a conclusion of error analysis.

本文首先叙述了制动主缸补偿孔测量仪的基本功能和技术指标，接着介绍了仪器的总体结构、检测原理与方法，重点对系统的主要组成部分，如内窥显微光学成像系统、CCD摄像机和精密机械系统等的工作原理进行了论述，并对光学成像系统进行了设计，最后分析了系统的主要误差来源及其对系统检测精度的影响，并给出误差分析结论。

The error correction method for microwave measuring line is analyzed, and a new method is proposed which can realize the measurement of error network parameters for microwave measuring line. Then the least square method explicit solutions of error network are given, and the CAT of error network parameters is realized.

分析了微波测量线误差校正的方法，提出了仅用小反射滑动负载即可确定测量线误差网络参数的新方法，给出了测量线误差网络参数的最小二乘法显式解，并实现了测量线误差网络参数的CAT 。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。