查询词典 measuring error

Based on the measurement sample stationarity in limited distance,the prediction model's limited astringency and mensurability to the dynamic measuring error and the prediction error respectively are proven.

首次研制成功了高精度任意二面角与圆分度测量系统，并编制了基于MS Windows的测量和系统控制软件。

Hypothesis in 0 ~ 10 speed range between 2000 and r/min speed error Δ requirement f r/min, more than 1 and measuring time, time than 100 ms t take 3 muon s acuities error Δ than eight mu t s, according to the formula (1) and (3) and assumptions, and computer programming.

假设转速范围在0～10 000 r/ min 之间，要求转速误差Δf ≤1 r/ min ，并且测量时间T ≤100 ms ，时间误差取3μs ≤ΔT ≤8μs ，根据公式(1)和(3)及假设条件，进行计算机编程求解。

By measuring missile movement inertia with torsion pendulum, the influences of periodic measurement error, systemic damp, period of swing object and corporative period of t he measured object and swinging object were analyzed. The relation among measurement error of movement inertia, measureme nt period, the period of swing object,corporaˉ tive period of tested object and swing object was proved. The maxi mal ratio between movement inertia for swinging obˉ ject and the measured object under conditions of different errors w as given under typical measurement precision.

通过扭摆测量导弹转动惯量的方法，分析了周期测量误差、系统阻尼、摆动体周期以及被测件和摆动体共摆周期对转动惯量测量精度的影响，得出转动惯量测量误差和周期测量误差、摆动体摆动周期、被测件和摆动体共摆周期之间的关系，给出了在典型的测量精度要求，不同的周期测量误差情况下，摆动体转动惯量和被测件转动惯量之间的最大比值。

Based on Taylor decomposition and the principal of matrix turbulence,the measuring error of structured light and error from light-plane calibration were analyzed,in which cross-ratio invariant was used in calibration of structured light system.

本文针对交比不变原理的结构光光平面标定方法，利用泰勒展开和矩阵扰动原理分别对系统的测量误差和光平面标定误差进行分析，提出了结构光测量系统的误差传递模型。

Deducing error equation that used vector rotating and transfer of axes theory,Measuring out measurement parameter error on different orthogonality by testing optical-electrical device.

提出误差推导的一种新方法，利用向量旋转及坐标系变换理论推导出误差公式。

It is very important to control the position error.A new method for measuring the boresight error between optical axes based on facular center located with vision image is presented.

提出了基于视觉图像定位光斑中心的轴偏角测量方法，并基于LABVIEW虚拟仪器平台构建了机器视觉测角系统。

The experiment results show that the measuring errors are more than 10' and these are zero point error and the non-lincar system error when the two obliquity angles of the kingpin are more than 15°, and the system errors increase as the kingpin obliquities increase.

试验表明：受检四轮定位仪当主销两倾角均大于15时，其测量误差大于10'，存在零点和线性度系统误差，且系统误差随主销倾角的增大而增大，从而解决了测量主销倾角量值检定的问题。

Uncertain upper boundary function is learned on-line by using FNN, and proportion controller strengthens the completeness of FNN control strategy. FNN is trained by using disparity target learning error produced by FIE. This can avoid supersaturating problem made by feedback error directly, and restrain influence of measuring noise and improve control performance.

由于模糊技术与神经网络的结合能弥补彼此的不足，因此本文提出了一种模糊神经网络控制器与比例控制器相结合的控制方案，采用模糊神经网络在线学习不确定函数的上界，比例控制器增强模糊神经网络控制策略的完备性。

In order to resolve the practical problem about measuring hobs with bigger modulus, a new method is put forward by which the circular adjacent pitch error and accumulated pitch error of hobs can be measured on the grinder.

针对大模数滚刀测量存在的实际问题，提出一种在磨床上测量滚刀容屑槽相邻周节误差和周节累积误差的新方法，并给出了测量实例。

A serial of precise standard resisters BZ-3 was used to adjust the instrument. The results showedthat the maximum error is less than 0.12%. The error is less than 0.05%in measuring the resistivity of several kinds ofenameled wire. For large piece of metal samples with low resistance, the instrument can have accurate results

通过对高精度标准电阻器组BZ-3的检测表明，全量程中的最大非线性误差为0.12％，对各种标号的漆包线的测量误差小于0.5％，对金属试样在腐蚀液体中的腐蚀情况能进行动态监测，对大试样粉末冶金样品的微小电阻也能进行精确的测量

I'm going tor her!

我这就去救她！

As rise are design to help keep a several toney , a brain chemical at continues lever.

SSRI被设计来帮助保持血液中的复合胺即在大脑中一个连续水平的化学物质。