查询词典 measurement

With the application of the sampling theorem and the Fast Fourier Transform, two groups of numerical forms of the algorithm equations suitable for two kinds of FFT subroutines are derived. Finally, the measurement algorithm is fully tested by the measurement and calculation carrier out for an MMW irradiator.

在解析算法的基础上，应用采样定理和快速傅里叶变换，推导了分别适用于两种快速傅里叶变换子程序的数值算法公式，通过对一种毫米波辐射器的实际测量和计算对测量算法进行了整体检验。

The effect on temperature measurement accuracy was analyzed by mechanical modulating disk in the real-time temperature measurement system using lasers InGaAs/I and pyroelectric detector LiYaO-3 based on Kirchhoff law.

分析了一种基于基尔霍夫定律的钽酸锂(LiTaO3)热释电探测器作为接收元件的实时测温系统中，机械式调制盘对测量精度影响，提出了改变机械式调制盘对测量精度的影响的方法；介绍了液晶调制器的结构、对辐射调制的原理以及在使用过程中的优点。

Based on the phase measurement principle of RF signals,the method of S-band relativistic klystron amplifier phase measurement was put forward.

基于高频信号相位测量原理，提出了S波段相对论速调管放大器相位测量的方法。

X-ray interferometry, which takes the very stable silicon lattice spacing as length unit for microdisplacement measurement, is an advanced technique for nanometer measurement.

X射线干涉测量技术以非常稳定的单晶硅晶格作为长度单位实现微位移测量，是国际上先进的具有原子尺度分辨率的纳米测量技术。

The mechanical measurement is to use an indicator to measure the surface or the edge of the testing lens mounted in a specific holder in a contact way. The principle of the optical measurement is the geometric optics, utilizing the properties of refraction or reflection of light to detect the centering error of the testing elements in a contactless way.

机械式的测量是利用指示器配合治具对待测透镜之外缘或表面进行接触式测量；而光学式的测量原理则是利用几何光学的折射或反射性质，对待测元件进行非接触式的偏心误差量测。

B. when precision testing equipment, the adjustment process: in the assembly process and equipment are completely assembled to precision testing and adjustment, such as boring bed in the installation process after grinding levelness and straightness calibration, an adjustment and measurement and cannot fully reflect the true error, and requires at least three times and measurement, can eliminate stress, and each must adjust time intervals, it takes about three days.

B。设备精度检测时的调整过程：设备在组装过程中及完全组装后均需进行精度检测及调整，如对镗床床身导轨磨削后在安装过程中的水平度和直线度的校验，一次调整与测量并不能完全反映出其真实误差，而至少需要三次调整和测量，才能消除应力的影响，且每次调整都需有时间间隔，故需时约3天。

Based on the projectile's geometry structure and movement characteristics, a non gyroscope inertial measurement technique using twelve linear accelerometers for the angular rate measurement and linear acceleration is presented.

基于炮弹的几何结构及运动特点，设计了一种十二加速度计组合的无陀螺惯性测量方案用于测量弹体运动时的角速度和线加速度。

This paper studied mainly mechanism about pneumatic sensor of small measurement range linear dimension measurement in pneumatic measure system concluding static stage and dynamic state characteristics study.

主要进行用于小量程线性尺寸测量的气动测量系统中气动传感器的机理研究，气动传感器静态特性研究和动态响应特性研究。

In this thesis, the fabrication of planar resonant tunneling diodes and mesa-type resonant tunneling diodes, the measurement and analysis of MOBILE(monostable-bistable transition logic element)circuit cell build up by planar resonant tunneling diodes, the measurement and analysis of series resistance of resonant tunneling diodes, and fabrication of resonant tunneling transistor are studied.

本论文包括了平面型共振隧穿二极管的研制、台面型共振隧穿二极管的制作、由平面型共振隧穿二极管组成的MOBILE单元电路设计与测试、共振隧穿二极管的串联电阻的分析与测试以及共振隧穿晶体管的研制等研究内容。

With the evaluation, each group measuring value is considered as a single subsystem, and the minmax-difference, mean difference and the mean square value of each group are calculated. Then, the ratio of the mean difference to the measurement mean value is defined as the system-relatively error of subsystem and the ratio of the minmax difference to the measurement mean value is defined as the accidence-relatively error of the subsystem.

以每组为一个子系统，分别计算出每组的极差、平均差和标准差，然后定义平均差和测量平均值的比值为子系统的系统相对误差，定义极差和测量平均值的比值为子系统的偶然相对误差。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。