查询词典 mean square of error

Error of indication of comparator was calibrated by using gauge block with conjugate method.

比较法测量量块的仪器的示值误差是采用配对法用量块校准的。

3 Indicator error calibration:示值误差校准: Take turns place the standard gauge blocks with measure 10mm,20mm,30mm,40mm,50mm in the middle of plane measure heads ,adjust the gauge block position , make the center plane and measure staff axes plane touch with gently, after tranquilization, read the display result .

依次将尺寸为 10mm，20mm，30mm，40mm，50mm 的标准量块放入平面测头之间，调整量块位置，使其中心面与测杆轴线面轻轻接触，待稳定后，读取显示结果，其示值误差应在±0.5um 内为合格，否则停用修理(每次测量块时，要重新清零)。

Under some reasonable hypothetic conditions,the error of inverse wavelet which is caused by non-orthogonality is nearly Gauss distribution.

通过分析非正交性对滤波器的影响，可以证明：逆子波因非正交性产生的误差呈近似的高斯分布。

One-dimensional time domain helicopter-borne electromagnetic responses are computed using G-S transform and Gauss numerical integral. The variation of electromagnetic responses due to bird height is analyzed, and then the variation of bird height is transformed to the variation of pseudo-layer thickness of zero conductivity to eliminate the error of the altimeter.

采用G-S变换以及高斯数值积分法，形成了时间域直升机的航空电磁响应正演样本集，分析了飞机测量过程中吊舱高度变化对电磁响应的影响，并将吊舱高度的变化等效成电导率为零的假层厚度的变化，以去除高度计等的影响。

Based on the platform of virtual instrument LabVIEW,this paper is to detect peaks of original signal respectively with power-weighted algorithm, Gaussian fitting algorithm, Gauss- polynomial fitting algorithm, a general polynomial fitting algorithm and Gaussian non-linear curve fitting algorithm, and compare their error means and standard deviations.

基于LabVIEW虚拟仪器开发平台，分析了功率加权算法、高斯拟合算法、高斯-多项式拟合算法、一般多项式拟合算法和高斯-非线性曲线拟合算法对原始信号寻峰，比较误差均值和标准偏差。

Secondly, we make the research of Xin.Li's LMS filter error concealment. It is based on the local stationary Gaussian process.

接着又对常用的Intra帧空域掩盖以及Inter帧的时域掩盖作了分析，讨论了误码的错误检测方法。

It is not made for that,it errs gayly , our gentle love, it has been said, error is human.

那位温柔的爱神生来并不是这样的，它嘻嘻哈哈四处乱撞，别人说过，撞错总也还是人情

While carrying out simulative program design for hobbing machining,the most difficult point is the description and modelling on the relationship between the cutter and gear blank both in space and in motion,especially the modelling of motion relation between cutter and gear blank in case there exists factors of error.

在进行滚齿的切削仿真程序设计中，其中最大的难点是对刀具和轮坯的空间关系和运动关系的描述和建模，尤其是存在误差因素时对刀具和轮坯之间运动关系的建模。

Gear-driven ; Long period error ; Optimization design ; MATLAB

齿轮传动；长周期误差；优化设计； MATLAB

Geat feelings will often take the aspect of error .

崇高的感情往往会采取错误的外表。

Summary In copyright infringement cases,if the alleged infringer uses or even plagiarizes the copyrighted works or parts thereof,which causes no substantially adverse effect on the normal exploitation of the work,nor does it inflict any substantial damages to the right owner,the de minis doctrine should be applied to exempt the liabilities of the defendant and seek the balance of interests between the right owner and the general public embodied by the copyright law.

在侵犯著作权案件中，如果被控侵权行为人虽未经著作权人的同意，使用甚至抄袭了受著作权保护的作品或作品的片段，但若情节轻微，未对该作品的正常使用产生任何实质不利的影响，亦未对权利人的权利造成实质性的损害，则应适用&不计琐细原则&，免除行为人的责任，以寻求在权利人利益与著作权法所体现的社会公共利益之间的平衡。

This new product will become our best seller.

这个新产品会成为我们最畅销的产品。