查询词典 maximum error

It also can be used to measure the geometrical tolerance, such as straightness error, roundness error, cylindricity error, parallelism error, perpendicularity error, angularity error, coaxiality error, symmetry error and circular run-out error etc.

该仪器集机、光、电于一体，采用了新的光路系统和近些年最新的测量方法及数据处理方法，具有功能多、体积小、重量轻、操作方便、非接触测量、测量精度高等特点。

In this paper, some characteristic functions of the multifunctional single-flank mesh gear tester of model CD320G-D which is applying gear integrated error measuring technique, computer technique, error separation technique, fault diagnosis technique and error prediction technique, including automatic searching of profile error start point, determination of profile barrelling, separation of profile form error and profile slope error, measurement of profile error with evaluation range subtracting tooth tip, measurement of tooth topograph and statistical analysis of gear manufacture error, are presented.

阐述了综合应用齿轮整体误差测量技术、计算机技术、误差分离技术、故障诊断技术和误差预报技术的多功能 CD320G-D 型单啮仪的一些具有特色的功能。这些功能包括齿形误差起测点的自动找定、凸形齿凸形量的测定及其形状误差与倾斜误差的分离、取值范围扣除齿顶部的齿形误差的测量、齿面轮廓度误差的测量以及齿轮加工误差的大样本统计分析。

Base Station type Software versionTypes of carrier frequency board adoptedTypes of combiner adoptedWhether had obtained the network license or notIndoor type or outdoor type Whether the master port is separated from the remote-port The maximum carrier frequency capacity of single cabinet The maximum supportable sector numbers of single cabinetWhether it is dual-carrier frequency board or notMust it be paired configuration if it's dual-carrier frequency board (namely, the type of single carrier frequency station could only configure the dual-carrier frequency on hardware) The maximum achievable configuration of a single station of the single cabinetReceiver sensitivity The maximum expand capacity of a single base station (the maximum number of TRX in configuration / the number of cabinets which is required)(fill in according with the three sectors) Top box transmitted power (given separately a grade one combine and a grade two combine) The maximum output power of amplifier (voice, a single logical carrier frequency) The maximum output power of amplifier (EGPRS, a single logical carrier frequency)Whether it has tower-interfaceWhether it has built-in lightning protectionWhether it support the ultra-long cover / whether it need for software support (give simple description that how hardware and software could achieve this) The supporting condition of EGSM (it should be supported including by the carrier frequency, combiner) Dual-band carrier wave (whether it supports the mixed use of 900 M/1800M in the same cabinet) The commonality of duplicate parts Whether it can built-in transmission unitThe single cabinet size (high × width × deep) Installation method Whether it can place against the wallThe basic frame full-configured weight and the supportable number of carrier frequencyThe expansion frame full-configured weight and the supportable number of carrier frequency

基站型号软件版本号采用载频板型号采用合路器型号是否已取得入网许可室内型or室外型是否是主远端分离单机柜最大载频容量单机柜最大支持的扇区数是否是双载频板如是双载频板，是否必须成对配置(即单载频站型只能硬件配置双载频)单机柜可达到的单站最大配置接收机灵敏度单基站最大扩展能力(最大配置TRX数/需机柜数)(按3扇区填写)机顶发射功率(分别给出一级合路与两级合路)功放最大输出功率功放最大输出功率(EGPRS，单个逻辑载频)有无塔放接口有无内置避雷装置是否支持超远覆盖/是否需要软件支持(简单描述软硬件如何实现)EGSM支持情况(包括载频、合路器均应支持)双频段载波（是否支持900M/1800M在同一机柜内混合使用）备件通用性是否可以内置传输单元单机柜尺寸安装方式可否靠墙放置基本架满配重量及支持载频数扩容架满配重量及支持载频数是否支持基本架与扩容架跨扇区满配功耗满配时重量供电方式机柜进出线方式合路器损耗合路能力：几合一单扇区最大支持几载频合路到一副天线/采用几个合路器单扇区载频达到需要增加一副天线时，是否支持两级合路换以不增加天线如两级合路插损为是否支持基带跳频和合成跳频每单个合路器在从低载频数向高载频数扩容时，是否还需要增加硬件可用性指标MTBFMTTR系统中断服务时间硬件是否支持EGPRS本次报价软件版本号开始支持EGPRS的软件版本号其他特点注： 1 应分别填写出来按照本次报价要求所采用的全部BTS型号和采用的合路器型号 2 列出本报价要求的全部室外型基站与高功放单元

The computation implies that the influence of truncation error of up/downwards continuation is about 0.001 m2·s-2, the maximum error is only 0.11 m2·s-2, which can be ignored in CHAMP gravity field recovery. The influence of the reference gravity field error of up/downwards continuation is less than 0.1 m2·s-2 in general, but the maximum error can reach 1.3 m2·s-2. To reduce this error, a high-precision gravity field model should be used in the up/downwards continuation.

计算表明：延拓误差中的截断误差部分影响量级约0.001 m2·s-2，最大误差仅为0.11 m2·s-2，可完全忽略；延拓误差中的参考重力场模型误差影响随参考场选取的不同而有所差异，整体而言小于0.1 m2·s-2，但最大误差可达1.3 m2·s-2，采用高精度的参考重力场模型能大大减小延拓误差影响。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

Second, the data checking and correction process, to understand the various sources of measurement error, its three main areas: equipment error (determined by the instrument itself, is an objective source of error), observation error (due to the technical level personnel a result of belonging to a subjective source of error), external influence error (subject, such as temperature, atmospheric refraction effects of external factors such as these factors are also constantly changing and difficult to control, belonging to a variable source of error).

其次，在对数据的检查和矫正的过程中，明白了各种测量误差的来源，其主要有三个方面：仪器误差（仪器本身所决定，属客观误差来源）、观测误差（由于人员的技术水平而造成，属于主观误差来源）、外界影响误差（受到如温度、大气折射等外界因素的影响而这些因素又时时处于变动中而难以控制，属于可变动误差来源）。

To analyze the pseudo phenomena caused by migration velocity error, the paper firstly studied the depth error between post-stack migration and prestack migration caused by same velocity error, and found the depth error was only relative to velocity error and had no direct matter with methods of depth migration (post-stack migration or prestack migration). Then the paper did numerical simulation of a complex lenticular body model with wave-equation modeling and migration, and found that the velocity error could not only induce depth error, but also could change the modality of construction and the event of subjacent layers. Furthermore, it could change the frequency of reflective event. They are the pseudo phenomena caused by migration.

从分析偏移速度误差带来的各种假象出发，本文首先对比分析了速度误差对叠后深度偏移和叠前深度偏移的影响，发现偏移剖面的深度误差仅与速度模型的误差有关系，与具体的偏移方法没有直接的关系；然后对一个复杂的透镜体模型进行了波动方程叠后正演和偏移计算，详细地讨论了不同的速度误差带来的各种假象，发现速度误差不仅会带来深度误差，而且会造成构造体的形态变化，下覆地层同向轴的扭曲，还可能引起地层同向轴的频率发生变化，给资料解释带来一定的假象。

Error analysis In order to analysis the pose error of the hexapod machine tool, considering the characteristics of the parallel mechanism,"analysis on the error prominency factors for the hexapod machine tool pose error"is proposed. Numerically, the error prominency factor can express the influence on the pose error of the tool resulted from the mechanism parameter error within the whole workspace.

四、位姿误差分析为了定量地对并联机器人机床位姿误差进行分析，结合并联机构的特点，首次提出了&并联机器人机床位姿误差放大因子分析法&，因位姿误差放大因子是反映机床机构参数误差对刀具末端误差影响大小的机床工作空间内的统计值，因此既可作为机床结构参数精度设计的依据又可对机构参数进行优化。

Studied present measuring methods" advantages and disadvantages, and presented the necessity and importance of researching propellant transient heat transfer.2.according to 130 and aeronautic 90 rocket projectiles" structure, analysed and acquired physical and mathematical models for propellant transient heat transfer, also designed propellant temperature field simulation units for test.3.acquired discrete transient heat balance equation and temperature calculation program, and gave contrasting curves between experimental temperature values and program calculating temperature values as well as maximum errors and average square root errors between them.4.by programs based on the first class boundary condition, worked out temperature distribution in propellant temperature field simulation units at different time, analysed temperature field distribution law and main elements affecting heat transfer, acquired propellant mass weighted average temperature and one at the half position of propellant maximum thickness as well as maximum errors and average square root errors between them.5.established transient heat transfer mathematical model and temperature calculation program for the third class boundary condition, drew contrasting curves between temperature experimental values and calculation values and gave maximum errors and average square root errors between them, got temperature distribution in the simulation unit at different time and main elements affecting heat conduction, figured out propellant mass weighted average temperature and one at the half position of propellant maximum thickness as well as maximum errors and average square root errors between them.

分析了现有测试方法的优缺点，提出了研究推进剂瞬态导热的必要性和重要性。 2。根据130和航90两种火箭弹的结构，分析得到了推进剂传热的物理模型和数学模型，设计了推进剂温度场模拟实验装置。 3。得到了离散形式的瞬态热平衡方程和温度场计算程序，给出了实验温度与程序计算温度值的对比曲线及其最大偏差与均方差。 4。利用程序求出了第一类边界条件下、不同时刻推进剂温度场模拟装置中的温度分布，分析了温度场的分布规律和影响传热的主要因素，求出了推进剂质量加权平均温度和最大肉厚1／2处的温度时间曲线并给出了两者之间的最大偏差与均方差。 5。建立了第三类边界条件下的瞬态导热数学模型和温度计算程序，求出了温度实测值与计算值的对比曲线并给出了两者之间的最大偏差与均方差，得到了不同时刻温度场模拟装置的温度分布与影响导热的主要因素，求出了推进剂质量加权平均温度和最大肉厚1／2处温度及两者之间的最大偏差与均方差，讨论并确定了能代表130和航90推进剂温度的特征点的位置。

The three groups were loaded and analyzed under the same loading according to the mean value of the bite force of incisors. RESULTS:(1)The maximum stress of dentin in group A was twice higher than that in group B. The maximum primary stress, minimum primary stress and maximum shear stress of group A were respectively 236.35, 228.83 and 218.05 percent of those in group B. The difference of maximum stress values of group B and group C was neglectable.(2) The maximum stress distribution of dentin in group A and group B was quite different (the stress was concentrated in labial and lingual side of the cervical dentin in group A, otherwise in group B it was concentrated in the area around the alveolar and the labial and lingual side of the dentin which was opposite to the tip of the cast metal post and core). The maximum stress distribution of dentin in group A and group B was almost the same.

结果：(1)从牙本质的应力大小来看，A组中牙本质最大应力值比B组中牙本质最大应力值增大了1倍以上（最大主应力、最小主应力和最大剪切应力A组分别是B组的236.35%、228.83%和218.05%），而B组与C组的牙本质最大应力值相差极小；(2)从牙本质的应力分布位置来看，A组与B组的牙本质最大应力分布位置相差甚远（A组主要集中在牙颈部唇舌侧肩台部的牙本质上，B组主要集中于牙槽嵴顶附近及铸造桩核尾端相对应的唇舌侧的牙本质上），而B组与C组的牙本质最大应力分布几乎在同一位置。

Putt your way through 36 fun-filled holes of minigolf on 3D designed courses with elevated greens, bunkers, bridges and water hazards, among other crazy obstacles.

您的推杆方式，通过36个有趣的填孔迷你的三维设计的课程，以提升绿党，掩体，桥梁和水的危害，除其他疯狂的障碍。

Some participles can be used either as attributes or as predicatives.

有些分词既可当定语用，也可当表语用。