查询词典 maximum element

A three-dimensional finite element spatial mechanics model for calculating the additional longitudinal force transmission between continuously welded rails and high-speed railway bridges is established by using solid element to simulate bridges as well as pier and abutment,using space beam element to simulate rails,using spring element to simulate the link between bridges and tracks as well as pier and abutment.

采用实体单元模拟桥梁及桥梁墩台、空间梁单元模拟钢轨、弹簧单元模拟桥梁与墩台及轨道之间的连接，建立梁—轨纵向相互作用三维有限元空间力学模型。以丰沙线永定河单线铁路桥梁、秦沈线沙河双线铁路桥梁对其进行计算验证。

The model adopts Drucker-prager ideal elastic-plastic stress-strain model, using contact pair element simulate the interface between the wall and soil, soil body use eight-nodes is parametric quadrilateral element, pile use beam element, and anchor rod use space link element.

模型采用Drucker-Prager理想弹塑性本构模型以及用接触面单元模拟了土与结构的相互作用，土体采用了八节点等参数平面四边形单元，桩采用了梁单元，锚杆采用了杆单元。

With a 586 computer and ALGOR FEAS software of finite element method, the static stresses of the equalizing bar are obtained by finite element analysis for three finite element models of beam, plate and brick element.

在微机586和ALGOR FEAS有限元软件环境下，对推土机平衡梁以梁、板、块单元为主分别建立了三种有限元模型和进行了有限元应力分析。

The finite element model included two types of main element: beam element for concrete and truss element for internal unbonded or external tendon. The end nodes of main elements were connected with internal constraints named MPC in ABAQUS. Spring elements with very large stiffness were set up at the place of the deviators of externally prestressed beams, or along the span with relatively little space of unbonded internally prestressed beams. The modified Riks method is utilized to trace the entire structural response of beams prestressed with unbonded tendon from zero to ultimate loads. The reliability of the analysis model is verified by analytical results of typical test beams in comparison with experimental ones.

该有限元模型由两类主单元组成，即混凝土梁单元和体内无粘结或体外预应力筋桁架单元；主单元的端部节点用ABAQUS的内在约束MPC连接；在体外预应力梁的转向块处，或沿体内无粘结预应力梁全跨并以比较小的间隔设置刚度足够大的弹簧单元。

In this paper, a 4-node plate element combined with rivet element and contact element is employed to analyze two typical rivet joint structures, i.e., lap joint and butt joint. The penetration between two sub-plates in the lap zone or butt zone is avoided by introducing contact element in the proposed FE model. Bending deformation and its effect on in-plane displacement of the two typical rivet joint structures are studied.

本文采用四节点板单元，结合铆钉单元、接触单元，建立了针对铆接搭接及铆接对接两种典型结构的有限元模型，并考虑了搭接或对接区内的接触问题，通过参数分析研究了铆接搭接和对接结构在拉伸载荷下的弯曲效应及其对面内位移的影响。

The mixed finite element formulas composed by cable element, bar element and space beam element, which can be used in the static and dynamic analyses. The wind load is simulated into multi-cross correlation random processes based on WAWS, and the wind load sampling in time domain can be obtained.

利用这些样本对CT结构和索托桥进行非线性动力的时域分析，再利用数理统计的方法对时域内的结果数据进行总结和分析。

The inner force of the line element for underground structure have been calculated using the traditional finite element mesh and high-order manifold method to guarantee the numerical precision of the line element and overcome the disadvantages due to the geometry error between the actual position and computational position of the beam and truss element in common use.

用传统的有限元网格和流形方法的高阶覆盖位移函数来进行地下结构的杆、梁单元计算，保证了线单元模拟的数值精度，同时又克服了常用的杆、梁线单元计算位置与实际位置不相符合从而带来计算误差和结构设计不便等缺点，提供了一种解决结构数值计算的较好的途径。

In the course of numerical calculation, the influence among asperities, the coupling problems of the variation of temperature and pressure on contact surfaces, the variation problems of the maximum temperature, maximum contact pressure, maximum stress were taken account into.

在数值计算过程中，着重考虑了微凸体之间的相互影响，温度变化与接触区域压力变化的耦合问题，最高温度、最大接触压力以及最大等效应力的变化问题。

Through finding a best fitting spherical surface, making the maximum deviation between aspheric surface and the best fitting spherical surface minimum, the maximum deviation at this time is just the maximum asphericity of aspheric surface.

寻找最接近球面，使其沿法线方向与非球面的最大偏离量最小，此时的最大偏离量即为非球面的最大非球面度。

Based on the invariance of maximum likelihood estimation, the sufficient and necessary condition under which the maximum likelihood estimation has invariance for the parameters are given, then it uses this conclusion to calculate the maximum likelihood estimation of σ^2 and ρ for bivariate normal distribution.

根据参数极大似然估计不变性原则，给出在一定条件下极大似然估计具有不变性的充分必要条件，并利用该结论计算了二元正态分布Z=的未知参数σ^2和ρ的极大似然估计值。

Putt your way through 36 fun-filled holes of minigolf on 3D designed courses with elevated greens, bunkers, bridges and water hazards, among other crazy obstacles.

您的推杆方式，通过36个有趣的填孔迷你的三维设计的课程，以提升绿党，掩体，桥梁和水的危害，除其他疯狂的障碍。

Some participles can be used either as attributes or as predicatives.

有些分词既可当定语用，也可当表语用。