查询词典 manual input

All voltage values, unless otherwise noted, are with respect to the midpoint between VCC + and VCC C. Differential voltages are at the noninverting input terminal with respect to the inverting input terminal.

所有的电压值，除非另有说明，关于之间的VCC +和VCC电压差分正处于中点是关于反相输入端同相输入端。

When a noise signal is present, a pilot signal and noise signal passing through a capacitor are applied to the inverting input port of the subtracter via a second MOS transistor to cancel the noise signal contained in the composite input signal.

当噪声信号时，一个试验信号与噪声信号通过电容通过应用通过一个晶体管第二马鞍山到减法反相输入端口，取消噪声信号的复合输入信号中。

This paper describes all time and frequency analysis parameters measured with a new correlation processor (capability up to 1 GHz sampling rates and up to five input data channels) for three input channels:(1) the 252Cf source ionization chamber;(2) a detection channel; and (3) a second detection channel.

本文介绍的所有的时间和频率分析参数相关的新的处理器（能力高达1 GHz的采样率和高达5个测量输入数据信道）3输入通道：（1）鐦源电离室；（2）检测渠道；及（3）第二次检测通道。

This exhibit in the shape of a pen is includes a large-screen indicator, which faces the video camera. The video-output terminal of the camera is connected to the video-input terminal of the indicator. The indicator constantly transmits its own images to the camera lens. Each time the indicator transmits an image, the image becomes smaller. The input and output signals are repeatedly iterated producing a series of similar, small graphs.

笔形展柜内有一台大屏幕显示器，另有一只摄像头与屏幕水平相对，摄像头的视频输出端与显示器视频端连接，显示其自身的像不断输入摄像机镜头，但每输入一次，图像就缩小一次，即输入与输出信号进行反复迭代，出现一系列逐渐缩小的相似图形。

Keyboard code location relative speed equivalence; Input dynamic average code length; Input speed code length; The reasonable index of key-Location distribution.

关键字］键位相关速度当量；输入动态平均码长；输入速度码长；键位分布合理指数。

In terms of high-touch keyboard layout, keycap shape, key-way handle all the updates to the user-friendly, not only to meet the input speed, enter the correct rate and to better meet the needs of user input and comfortable.

高触感键盘无论在布局、键帽形状、键程手感上全部进行了人性化更新，不仅满足输入速度快、输入正确率，更能满足用户输入舒适的需求。

Using sensor output data as the compensator input, and the sensor input data as the compensator output, the compensator is designed based on the nonlinear dynamic Laguerre function.

用传感器的输出数据作为补偿器的输入，传感器的输入数据作为补偿器的输出，进行基于Laguerre函数的非线性动态补偿器的设计研究。

However, when the skew between input data and the input clock is close to half step time, the "three times oversampling" system can not detect whether the skew leads or lags, and may induce errors in recovered data.

当输入资料偏移量接近二分之一步距时，三倍取样架构将无法分辨出偏移量是领先还是落后取样时脉，因此可能造成恢复资料的出错。

When left floating open, any differential input will disable operation due to input pulldown resistors forcing an output default state.

当悬空开放，任何差分输入操作将禁用因输入下拉电阻迫使输出默认状态。

After being connected with a resistor in series, the primary input end of a transformer is connected with the output end of the live wire and the output end of the null line in parallel, the secondary output end is connected with the two ends of the earth wire switch in parallel after being connected with another resistor in series, one end of a neon lamp in a photoelectric coupler is connected with the input end of the earth wire E and a secondary end of the transformer, the other end of the neon lamp is connected with the centers of the two resistors, one end of a light sensitive resistor in a photoelectric coupling switch is connected with the anode of an integrated circuit power in the creepage protector, the other end of the light sensitive resistor is connected with the anode of a diode, the cathode of the diode is connected with the triggering pole of the silicon-controlled rectifier in the creepage protector, the neon lamp and the light sensitive resistor are positioned into a dark box, and a small hole which avoids the light sensitive resistor is formed on the dark box.

防止地线触点未导通的全能安全插头，包括各带开关的地、零、相三线接线和由零序互感器、脱扣器、放大器、整流器、试验回路和可控硅组成的漏电保护器，变压器初级输入端串联电阻后并接在火线输出端和零线输出端，次级输出端与电阻串联后并联在地线开关两端，光耦内氖灯的一端与地线E输入端和变压器次级的一端连接，氖灯另一端与二电阻的中心连接，光电耦合开关内光敏电阻的一端与漏电保护器内的集成电路电源正极连接、光敏电阻的另一端与二极管的正极连接，二极管的负极与漏电保护器内的可控硅触发极连接，氖灯和光敏电阻置于暗箱中，暗箱上开一避开光敏电阻的小孔。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。