查询词典 major axis

In order to achieve the setting up angle should be monitored and debugged, a new approach is brought up. With the CCD receiving the focusing spot of parabolic mirror, while rotating the parabolic mirror, collecting the focusing spot location information, the eccentric angle between the optical axis and the structural central axis could be found. System principle and design have been studied.The experimental results meet the need to test and monitor to the setting up angle of the discal parabolic mirror.

为了实现对抛物面反射镜的装配角度进行监控和调试，提出了一种通过CCD接收回转抛物面镜的聚焦光斑，同时旋转抛物面镜，采集光斑重心位置信息，从而计算出光轴与结构中心轴之间的偏心角的实现方案，并从方案原理和设计上对其进行研究和实验，实验结果证明该系统能应用于对盘状抛物面反射镜装配角度的测试和监控。

The exchange of the electrovalence of the cupric ion has been testified by XPS-ESCA.Graphite and chloride in the stage structure,seem to be the conductor and insulator,which form the "sandwich" structure.This special structure produced a weak chemical bond belt and provided the carrier space in the perpendicular direction to the c-axis.These factors in and vertical to the direction of c-axis together increased the electrical properties.

GICs将良导体的石墨层与绝缘体的氯化物层在分子尺度上结合起来，所形成的阶结构相当于许多导体和绝缘体层组成的"三明治"结构，产生化学键薄弱的通道，提供了垂直c轴方向的载流子通道，隧道效应和格架空间提供了载流子活动空间，这些因素共同作用使得GICs的电导率成倍增加

The true action is only to be secured when the amount of ellipticity is exceedingly slight, the centre of motion of the revolving piston-shaft being in a line intersecting the minor axis, at about one-third of the length of such an axis.

真正的行动只是被担保的数额时，椭圆是非常轻微的，该中心的议案，旋转活塞轴正处于一条线相交的轻微轴，在约三分之一的长度，例如一轴。

Sonographic examinations of the pancreas were performed by sagittal scanning at the epigastrium; the long axis and short axis of the oval cross-sections of both the pancreatic head and body were measured.

检查测量的方式是在上腹部作纵向扫描，可以分别得到胰脏头部与体部之圆形纵切面造影，进而分别测量胰脏头部与体的长轴与短轴，一共为4个胰脏因数。

All kinds of errors that influence load sharing characteristics of gear system have been given, mainly including manufacturing and assembly error of each gear component's axis and each bearing's axis, tooth thickness error. The formulas of equivalent mesh error have been derived.

确定了影响行星齿轮传动系统均载特性的各类误差，主要包括：各个齿轮构件的中心轴线制造和安装误差、轴承中心轴线的制造和安装误差、行星架的制造误差、齿轮的齿厚偏差。

InWürth's scheme, it is stays identical with the main axis, whereas inEvert's scheme, it is excentric from the common axis and rotates aroundit with an angular speed depending from the cogs'ratios.

在沃思的计划，这是保持一致的主轴，而在埃弗特的计划，这是偏心的共同轴和它周围旋转的角速度而从螺丝钉'的比率。

First, the wheelset is fixed and rotated by the device used hi vehicle depot as usual. Second, the center line of wheelset axis is determined by a device called axis-center probe. Last, the acting device for sensor can draw a whole felloe profile, which is made up of parallel-pole device and rotating-probe.

鉴于此，本文给出了一种全新的测量方案：采用车辆段普遍使用的转轮器实现被测轮对的定位；采用车轴基准探尺测定被测轮对的轴线；采用并联式伸缩机构和旋转测头作为传感器的执行机构，测定轮辋断面的轮廓线。

The precision of a new project for measuring the wheelset geometric parameters is studied once again in this paper. First, the wheelset is fixed and rotated by the device used in vehicle depot as usual. Second, the center line of wheelset axis is determined by a device called axis-center probe. Last, the acting device for sensor can draw a whole felloe profile, which is made up of parallel-pole device and rotating-probe.

本文研究一种新的非接触测量方法的精度，测量方法的核心是：采用车辆段普遍使用的转轮器实现被测轮对的粗定位；采用车轴基准探尺确定被测轮对的轴线；采用并联式伸缩机构和旋转测头座，带动电涡流位移传感器扫描车轮外形轮廓线，得到相关参数。

The average lengths of polar axis of Ferula and Heracleum are 29.67 and 34.07μm in which there are significant difference by rank-sum test, but the average width of equatorial axis are 17.07 and 15.65μm in which there are no significant difference, furthermore, the L/W are 1.76and 2.19 in which there are significant difference.

阿魏属和独活属植物的极轴平均长度分别为29.67μm和34.07μm，秩和检验表明二者差异显著；赤道轴平均长度17.07μm和15.65μm，差异不显著；极轴长/赤道宽的平均值分别为1.76和2.19，差异显著。

On the basis of direct modelling method by using extended Kalman filter, a new method combining extended Kalman filter with adaptive extended Kalman filter is presented to model gyro drift directly from rotate angle of turntable. Extended Kalman filter has great estimation error, what is more, may be divergent if the model and noise statistic are not accurate or wrong. The new method solves the problem of general extended Kalman filter by using fictious noise with timevarying statistic to compensate the linearized model error of extended Kalman filter. The parameter estimators of single-axis and double-axis servo test are designed from it.

本文深入研究了根据伺服试验数据进行陀螺仪漂移误差模型建模的方法，在应用广义Kalman滤波器直接建模的方法基础上，针对广义Kalman滤波器对于不精确或错误的模型和噪声统计，估计误差较大，甚至滤波发散的缺陷，借助于用带时变噪声统计的虚拟噪声补偿广义Kalman滤波的线性化模型误差的新思想，提出了用广义Kalman滤波和自适应广义Kalman滤波算法相结合的方法由转台的转角数据直接建模陀螺仪漂移误差模型，并设计了陀螺仪单轴伺服和双轴伺服测试时参数估计的滤波器。

The work of this paper is as follows: 1. Looking back the progressing history of the linear motor, introducing the features of the elevator driven by linear induction motor, radicating the topic of this paper "the digital frequency variable control of the elevator bi-side direct driven by linear induction motor". The research of this paper covers the conventional VVVF control, space vector based VVVF control, vector control and DTC.

本文主要开展了以下几个方面的工作： 1 回顾了直线电机发展历史，电机的驱动技术演变，特别是针对直线电机的驱动，简要介绍了直线感应电机驱动电梯的优点和不同结构类型，对传统的v／f控制，基于空间矢量法的v／f控制，矢量控制，和基于电压空间矢量的直接转矩控制进行了比较，确立了本课题的研究主题：直线感应电机双边直推式驱动电梯的全数字变频控制。

The article combines with the treatment of a superficial civil air defense work to introduce how the grouting method to improve the performance of the backfill soil.

文章从治理漂浮人防工事的角度提出了注浆技术在改善回填土性质方面的应用，并详细阐述了注浆技术的施工流程。