查询词典 magic circle

Under the round icon state, move the cursor to the position of centre of a circle (according to the position value of the cursor, or the cursor is reached and turned into ' X ' shape while appointing one), can't show, move the cursor at the same time, will reveal the present and round radius in the parameter window springing, will draw the corresponding round (when far away from the centre of a circle in cursoring on the screen, the radius becomes large; When the cursor is close to the centre of a circle, the radius is diminished).

有关机械方面的翻译，谁会，帮我翻译一句8.3.3.1圆输入 A ：标定圆在圆图标状态下，将光标移至圆心位置（根据光标位置值，或光标到达指定点时变成'X'形），不能放，同时移动光标，在弹出的参数窗内将显示当前圆的半径，屏幕上绘出对应的圆（当光标远离圆心时，半径变大；当光标靠近圆心时，半径变小）。

Consider the circle that is tangent to the curve at and has the same curvature there. Its center will lie on the concave side of the curve. This circle is called the circle of curvature. Its radius is the radius of curvature, and

在点处的曲线的法线上，在凹的一侧取一点，使得，以为圆心，半径为的圆叫做曲线在点处的曲率圆，曲率圆的圆心叫做曲线在点处的曲率中心，曲率圆的半径叫做曲线在点处的曲率半径。

Carried out generalized Mises yield criterion , yield curve on the n flat face was circle curve, and different elected parameters correspond to external angular point circumcircle、 internal angular point circumcircle and incircle of Mohr-Coulomb unequiangular hexagon. According to unequiangular hexagon, circle yield curve which had the same area as hexagon can be found, and corresponding yield criterionwas equilateral circle yield curve.

3广义米赛斯准则在π平面上的屈服曲线为圆曲线，选择的参数不同对应有莫尔—库仑不等角六边形的外角点外接圆，内角点外接圆和内切圆，对于不等角六边形，还可以找到一个面积和六边形相等的圆屈服曲线，对应的屈服准则为等面圆屈服曲线。

It showed the correctness of the criteria of roundness error and relationship between the minimum zone circle, minimum circumscribed circle and maximum inscribed circle and the effectiveness of the methods for evaluation of roundness error.

也验证了圆度误差判别准则及最小区域圆、最小外接圆和最大内接圆特征点间的相互关系的准确性和误差评定方法的有效性。

The criteria of the minimum zone circle method, minimum circumscribed circle method and maximum inscribed circle method were researched and the criterion of obtuse triangle was proposed.

研究了圆度误差评定中最小区域圆法、最小外接圆法和最大内接圆法的判别准则，提出了具有最小误差的外接圆和内接圆的钝角三角形准则，使圆度误差的判别准则得到完善。

According to the characters of debris flow and risk controlling condition in mountain towns, The concentric circle theory of geography is introduced in this paper, The concentric circle model for debris risk control in mountain towns is discussed and the effect of "concentric circle model" in hazard risk control is analyzed.

针对山区城镇泥石流危害特征及风险控制现状，引入地理学中的同心圆理论，探讨了山区城镇泥石流风险控制的"同心圆模式"，分析了"同心圆模式"中各风险控制层对灾害风险的控制机制及效应，提出城镇泥石流风险控制应遵循多层防范、逐级降低的思路，研究可为山区城镇的减灾管理提供合理的参考。

Stub Pitch is a number used to denote the radial distance from the pitch circle to the major circle of the external spline and from the pitch circle to the minor circleof the internal spline.

残余径节：残余径节是一个数，它用于表示节圆与外花键的大圆或内花键的小圆之间的半径差。

Range is divided into basically forces opened fire on lap three, opened fire in the Green circle, basically for a median of mass destruction, the role of principal in order to reduce the morale of the enemy, yellow circle, I sides opened fire on the enemy's main regions, the role of the main anti-soldier , a red circle for the distance, often can lead to greater destruction, but more for the melee area.

基本上部队开火范围分为3个圈，在绿圈开火，基本上杀伤力为个位数，起到的作用主要为降低敌人士气，黄圈为敌我双方开火的主要区域，作用主要是杀伤士兵，红圈为最近距离，通常可导致更大的杀伤力，但更多情况为melee区域。

First of all, to the yellow circle voltigeur shooting the enemy, or green circle in the first row only shooting mission to induce the enemy close to the yellow circle and then after the two rows of continuous shooting, a close fight but the remnants of the enemy, immediately removed voltigeur , fusilier pull up hand-to-hand, at the same time do not forget to put first shot.

首先以voltigeur在黄圈内向敌人射击，或者在绿圈内仅使用第一排射击，诱使敌军团接近，然后在黄圈内连续射击后两排，一但残余敌人接近肉搏，马上撤下voltigeur，拉fusilier上前肉搏，同时别忘了先放一枪。

The hour hand: the circle of a clock face is divided by 12 hours, so each hour is 1/12 of the circle, and since a circle is 360 degrees, each hour is 360/12 degrees, so the angle of the hour hand is calculated this way, but as you all have noticed, no analog clock's hour hand stands still exactly on the current hour number until an hour is passed.

时针：在时钟面圆除以12小时，所以每个小时的1 / 12圈，由于圆是360度，每一个小时是十二分之三百六度，所以时针的角度这种方式计算，但大家都已经注意到，没有模拟时钟的时针上的立场仍有当前小时一个小时，直到完全通过。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。