查询词典 machine direction

Description: This project shall adopt the double-mixing-shaft reciprocal rotary distribution design, with the vibration excitation/isolation system to be floating-connected by double-seated spring and hydraulic system adopting highly-dynamic performance proportion, making unnecessary a separate motor for driving and ensuring high compactness of blocks. The machine should make less noise than similar products, operate quickly, reduce the impact upon change of direction and save energy. Each joint should be linked with knuckle bearing and provided with lubricating device to prevent wear and tear. The automatic control system should use PLC and HMI display of operation, providing accurate and explicit detection of faults.

内容说明：本项目采用双搅拌轴往复旋转布料设计，激振隔振系统采用双座双弹簧浮动连接，液压系统采用高动态性能比例，可使砌块成型机不需要单独电机驱动，能保证砌块密实度大；机台噪声比同类机台小，运行快速，降低变向时的冲击配备，节约能源；各关节部位均用关节轴承联结，具备润滑装置不易磨损；自控制系统选用PLC编制控制器，操作人机界面显示，故障准确明确。

Along with the development of science technique, traditional combined machine based on relay-control cannot adapt to the advanced productivity , in that case, the programmable controlling technique ,with its flexiblity, high reliability,good generalization,gradually replaced the relay-control, becoming the main development direction of the contemporary industry control.

随着科学技术的不断发展，传统的以继电器控制为基础的组合机床愈加与先进生产力不相适应，在这种情况下，可编程序控制技术以其灵活性好，可靠性高，通用性强，逐渐取代了继电器控制方式，成为当代工业控制的主要发展方向。

Along with the development of science technique traditional combined machine based on relay-control cannot adapt to the advanced productivity in that case the programmable controlling technique with its flexiblity high reliabilitygood generalizationgradually replaced the relay-control becoming the main development direction of the contemporary industry control.

随着科学技术的不断发展，传统的以继电器控制为基础的组合机床愈加与先进生产力不相适应，在这种情况下，可编程序控制技术以其灵活性好，可靠性高，通用性强，逐渐取代了继电器控制方式，成为当代工业控制的主要发展方向。

The blender of this device adopts flexible shaft joint, easy to disa-ssembly and dean. When user dismmltle machine, please mind the bolt location of blender run direction.

本设备搅拌总成采用活套连轴器连接，便于拆装，用户拆装时，请注意上下搅拌方向位置螺钉部位。

In this paper,Litvin's Local Synthesis Method was used to determine all machine-tool settings for HGM and HGT cutting,with which the location of oontad area,the dimension of contact ellipse,the direction of contact path,the shape and magnitude of transmission error of machined hypoid gear drive can satisfy prescribed requirement aoeurately.

本文应用Litvin的局部综合方法进行了准双曲面齿轮切齿设计的推导。通过一次计算便能获得HGM和HGT加工的准双曲面齿轮的全部切齿参数。

From the burden increased aspect clarify set upthe necessity of station, then pass to drew up to set up generalizeof transformer substation and line direction to consider, and passto analysis of carry the data, safety, economic and dependableconsider and made sure the 110 kV, 35 kV, 10 kV and station useelectricity of lord connect line, then again through burdencalculation and power supply scope made sure main number, capacityand model number of the transformer set, also in the meantime makesure the station uses capacity and model number of transformer,end, according to biggest keep on work electric current and shortcircuit calculating of calculation result, to the high pressureRong break a machine, insulate a switch, female line, insulate sonand wear a wall set tube, electric voltage with each other feelingmachine, electric current with each other the feeling machinecarried on choose a type, thus completed a 110 kV electricity apart of design.

本文首先根据任务书上所给系统与线路及所有负荷的参数，分析负荷发展趋势。从负荷增长方面阐明了建站的必要性，然后通过对拟建变电站的概括以及出线方向来考虑，并通过对负荷资料的分析，安全，经济及可靠性方面考虑，确定了110kV ，35kV ，10kV 以及站用电的主接线，然后又通过负荷计算及供电范围确定了主变压器台数，容量及型号，同时也确定了站用变压器的容量及型号，最后，根据最大持续工作电流及短路计算的计算结果，对高压熔断器，隔离开关，母线，绝缘子和穿墙套管，电压互感器，电流互感器进行了选型，然后进行配电装置和平面布置的设计以及防雷的设计，从而完成了110kV 电气一次部分的设计。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。