查询词典 m.

Programme simulation: Simulate the process of the queuing according to queue model M/M/1, programming language C, the four steps such as data coming, waiting in queue, link service and data leaving.

程序模拟：本程序是以M/M/1为排队模型，使用C语言进行程序设计，通过数据到达、排队等待、链路服务、数据离开四个环节模拟了排队过程。

In this paper, m/M/1 model in queuing theory is applied to Ethernet modeling with light load.

本论文运用排队论中的m／M／l模型对轻负荷的以太网进行建模。

Lastly, we study the conditions of linearization for symmetric system, from which we can see that a symmetric system is linearizable on manifold M if and only if this system is linearizable on quotient manifold M/G.

最后讨论了对称非线性系统线性化问题，从中可以看出对于具有对称性的非线性系统只要在商流形M／G上能满足线性化条件即能保证在整个流形M上能线性化。

The instantaneous SNRof the receiver of STBC over raying fading is illustrated, based on this, the closed impression of STBC's symbol error rate is educed with M-PSK and M-QAM modulation and also presents the numerical results.

给出在瑞利衰落信道下正交空时分组码瞬时接收信噪比的一般表达式，在此基础上推导出正交空时分组码在M-PSK和M-QAM调制下误符号率的闭式表达式，并给出数值分析结果。

The size of the rectifier is 180μm��140μm.

整流器的面积为180μm×140μm。

Furthermore, they gave a conjecture: if M and M are reducible or ?

本文证明了如果M和M都是可约流形，那么Δ≤2。

Results show that sulfides can be refined and disperse evenly after continuous multi-pass rolling, with the average width of sulfides being 4.91μm, the average length being 14.27μm, the average aspect ratio being 3.03, and the average area being 44.72μm2. The sulfides can refine the microstructure due to their pinning effect, and the reefing effect shows Zener relation.

结果表明，连续、多道次变形的轧制工艺能够使硫化物破碎并均匀弥散化，硫化物平均宽度4.91μm，平均长度14.27μm，平均长宽比3.03，平均面积44.72μm2；硫化物组织细化的原因是作为第二相粒子钉扎晶界，硫化物颗粒细化组织满足Zener关系。

It is shown that both strength and delayed fracture resistance of 42CrMoVNb steel increase when its grain size is refined from 20 m to 4 m, but they do not increase when refined to 2 m.

结果表明，随着晶粒细化， 42CrMoVNb钢的强度和缺口拉伸延迟断裂抗力逐渐提高；但当晶粒细化到2 m时，强度和延迟断裂抗力均不再提高。

The results show that the grain size is refined by the addition of Nd or Dy, especially combined addition is better than single addition. With the addition of 0.2 % Nd and 0.6% Dy, the grain size is reduced from 150 μm to 60 μm. Combined addition with two rare earths elements makes the tensile strength, yield strength and elongation of ZK10 alloy increase to 191.0 MPa, 69.0 MPa, and 16.6%, increasing by 89%, 43%, 232% respectively, compared with ZK10 alloy without RE element.

结果表明：ZK10镁合金中分别加入Nd和Dy均能细化晶粒，且Nd和Dy同时加入的效果优于单一加入的效果，当同时加入质量分数为0.2% Nd和0.6% Dy时，合金的平均晶粒尺寸由原来的150 μm细化至60 μm，使ZK10合金的抗拉强度和屈服强度分别提高至191.0 MPa和69.0 MPa，伸长率达到16.6%，与未加入稀土的ZK10合金相比分别提高89%，43%和232%。

The results show that dynamic softening is easy to occur in these ingots and flow stress becomes steady finally; the material constants of hot deformation are procedural parameters that stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q are all increased with strain increasing, while stress exponent n is decreased gradually; the values α and m of the alloy homogenized are the biggest and the value n is the smallest, dynamic softening effect of the alloy is the most obvious, which can deform evenly; influence of strain on the value Q of the alloy homogenized is a little and the average value of Q is only 176.5kJ/mol, so the alloy is easy to deform; the alloy matrix shows the regular recrystallization grains when the strain is 50%; dislocation cell structure re-formed in the grains with increase of strain.

结果表明：经不同处理的Al-1Mn-1Mg合金均易发生动态软化并最终呈现稳态流变特征；热变形材料常数是过程量，随应变量的增加，应力水平参数α、应变速率敏感性指数m和热变形激活能 Q 随之增大，而应力指数 n 则逐渐减小；均匀化退火后，铝合金的α和m值最大而n值最小，动态软化效果最明显且变形均匀，在该状态下，铝合金的 Q 值受变形量影响小，平均仅为176.5kJ/mol，易进行热变形；当应变量为0.7时，基体呈现规则的再结晶晶粒组织，随着应变量的增加，晶内重新形成了位错胞结构。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。