查询词典 low-pressure

Impact of population growth on resources environment: population explosion's pressure to land resource, population growth's pressure to biological resources, population explosion's pressure to water resources, population inflation's pressure to energy.

人口增长对资源环境的影响：人口爆炸对土地资源的压力，人口增长对生物资源的压力，人口爆炸对水资源的压力，人口膨胀对能源的压力

By making use of multi-points backward pressure of one dry gas well, this paper introduces how to confirm dynamic friction coefficient of downhole tubing at the exact moment through stable testing material, gives the productivity and the corresponding bottom hole pressure by using productivity equation, calculates wellhead pressure in combination with dynamic friction coefficient of tubing, establishes the correct wellhead outflow performance equation for this well, draws out wellhead outflow performance curve and discusses how wellhead outflow performance equation or wellhead outflow performance curve changes with the decrease of formation pressure or the change of wellhead outflow performance curve.

借助1口干气井的多点回压法试井资料，介绍了如何利用气井稳定试井资料，确定该气井此时此刻井下油管动态摩阻系数；利用产能方程给出产量和对应的井底压力，结合油管动态摩阻系数计算井口压力，建立该井准确的井口流出动态方程并编绘井口流出动态曲线；讨论了随着地层压力递减和井下油管动态摩阻系数变化规律，井口流出动态方程或井口流出动态曲线的变化规律。

Near the center, the pressure gradient force (from the pressure in the center of the cyclone compared to the pressure outside the cyclone) and the Coriolis force must be in an approximate balance, or the cyclone would collapse on itself as a result of the difference in pressure.

中心附近的气压梯度力（从压力中的中心气旋的压力相比，外气旋）和科氏力，必须在一个大致平衡，或气旋将会崩溃对本身所造成的差异在压力。

By using Lee\'s matching law, the excess pore-air pressure, excess pore-water pressure and settlement in the Laplace-transformed domain are obtained for one-dimensional consolidation in unsaturated soils, under the large-area uniform instantaneous loading. A computer program using the method by Crump and Durbin is developed to obtain the semi-analytical solution of the excess pore-air pressure, excess pore-water pressure and settlement under the boundary conditions of the top surface permeable to water and air and the bottom impermeable to water and air.

8采用李氏比拟法，应用Merchant粘弹性模型，得到了Laplace变换域内粘弹性非饱和土地基一维固结时超孔隙水压力，超孔隙气压力以及土层沉降的解；采用Crump及Durbin方法实现Laplace逆变换，获得大面积均布瞬时加荷，在顶面排气排水，底面不排气不排水情况下粘弹性非饱和土地基一维固结时的半解析解。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature.Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

The pressure drop of the compound tray can be regarded as consisting of dry plate pressure drop, clear liquid resistance, liquid surface tension resistance, and packing pressure drop. The model that has established can fairly predict the pressure drop of the compound tray, the value calculated by the model compared with that detected by experiment is less than 20%.

复合塔板的压降可认为由干板压降、清液层阻力、填料层压降和克服液体表面张力的压降四部分组成，所建立的压降计算模型，能较好地预测复合塔板的压降，计算值与实验值误差在±20％以内，可用于工程设计。

By using the CFD software FLUENT, the inner-flow field of centrifugal fans with ruled-surface impeller versus with enveloping surface impeller has been simulated. The static pressure distribution, the dynamic pressure distribution, the total pressure distribution, the turbulent intensity and the speed vector of the two kinds of centrifugal fans are then analyzed and compared. From the calculating results, we found that the pressure distribution, the speed vector and other parameters of the two kinds of centrifugal fans are basically same. This implies that the tool-path generating arithmetic for the machining of the impeller can meet the aerodynamic requirements of the centrifugal fan. Furthermore the method can provide proof for designing department to establish sound manufacturing tolerance for impeller.

最后采用CFD软件FLUENT，利用标准k-ε湍流模型，采用分离隐式求解器，分别对直纹面叶轮离心通风机和包络面叶轮离心通风机整体风机内部三维流场和单个通道流场进行了数值模拟计算，在计算结果的后处理中，对相同坐标值处的静压力、动压力、湍流强度和速度矢量等参数进行了分析与比较，结果表明：在相同的计算参数条件下所得到直纹面叶轮离心通风机和包络面叶轮离心通风机内部流场差别不大，从而揭示所采用的叶轮数控加工的刀位规划方法的规划误差对流体机械动力性能的影响不大，这也为设计部门制定合理的叶轮加工公差提供了依据。

On the aspect of error compensation, the system using the geometric average sound pressure instead of the arithmetic average sound pressure to get the sound pressure of the measurement point. This method not only reduces the high frequency error in the sound intensity measurement, which compensates the finite difference approximation error, but also greatly reduces the computation of the sound pressure spectrum.

误差补偿方面，课题采用几何平均声压代替通常的算术平均声压来计算双传声器法的声场声压值，这样不仅可以有效的减少声强测量中的高频误差，对有限差分误差起到了补偿作用，而且还大大减小了声压谱计算中的计算量。

Green function defined inphase space differs from one in coordinate space by its struc-ture which exhibits nonlocatity in coordinates and oscillatorybehavior with respect to momenta.

在相空间中定义的Green函数不同于通常坐标空间的Green函数，在结构上显示出对坐标的高度非局域性，而对动量则显示出振荡行为。

The upper front part of a saddle;a saddlebow.

前鞍桥马鞍前面的上部分；前鞍桥