查询词典 locknut
- 与 locknut 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Inlet side has a machined flange and male straight-pipe threaded for locknut.
进口端有一个机加工法兰和直线管道外螺纹,用于防松螺母。
-
For locating bearing positions and CARB bearings insert a locating ring between the bearing outer ring and housing shoulder on the locknut side of bearing.
为将定位轴承和CARB轴承的位置定准,将一个定位环插放到轴承外圈和轴承座挡边之间、轴承锁紧螺母的一侧。
-
Secure with locknut and gaskets.
用放松螺母和垫圈紧固。
-
By experiments,three sources of the antilock friction moment and the static antilock friction performance on the Fe-based SMA locknut were tested separately,as a result the feasibility of the new-type nut was proved.
通过试验对铁基SMA螺母防松摩擦力矩的三个来源和静态防松性能分别进行了测定,从试验的角度证明了这种螺母的防松性能。
-
Recheck clearance again after tightening locknut. Readjust clearance as necessary.
拧紧防松螺母后,再一次检查间隙,视需要重新调节间隙。
-
Tile fixed mould-plate is accessed to accommodate the head of the length-bolt and a clearance hole is provided in the moving mould plate to accommodate the nut and locknut.
定模板有一个沉孔,容纳长螺栓的头部,动模板上有个间隙孔,以容纳螺帽和并帽。
-
If valve clearance needs to be adjusted, loosen the locknut on rocker arm adjusting screw. Turn adjusting screw until feeler gauge slips with a slight drag.
如果气门间隙需要调节,松开摇臂调节螺丝上的防松螺母,转动调节螺丝直到测隙规滑动时稍带阻力为止。
-
The proper clearance setting should be at 0.04-0.1mm. The adjustmentscrew. Tighten the locknut after the adjustment is achieved. Alter theinitial 1 hour adjustment, this procedure should be performed a fewevery 2 hours of use.
正确的汽门间隙为0.04-0.1mm之间,间隙调整螺丝被一个固定螺帽固定住,先将固定螺帽放松就可以转动间隙调整螺丝(如图2)调整后每一小时检查固定螺帽有没有松掉,每2个飞行小时检查汽门间隙。
-
The fuel tank assembly consists of: the fuel tank, fuel pump module assembly, fuel pump module locknut/gasket, and rollover valve (refer to Group 25, Emission Control System for rollover valve information).
油箱组合包含:油箱,油泵模组组件,油泵模组锁定螺帽/垫圈,和逆止阀(请参阅单元25&排放控制系统&来获取逆止阀资讯)。
-
If the set weight need to be changed, you can control the lift weight according to the screw pillar's position in the 750-1000kg When adjust, loosen the locknut, every a ring going up, the set lifting weight can add 200kg, every a ring going down, the set lifting weight can reduce 200kg
4.2.3如需改变设定重量,可以在750-1000㎏范围以内,根据调整螺柱的位置不控制起升重量(调整时,先松开锁紧帽,调整每上行转一圈,原设定起重载重量增加200㎏,每下行转一圈原设定载重量减少200㎏,调整好后,用锁紧帽锁紧)。
- 推荐网络例句
-
This paper discusses design and realizable methods of remote test output interface from logical design angle.
本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。
-
This also 星体投射plies to buildings, structures and geological features.
这也适用于建筑物和地质特征。
-
We all hope for a better life.
我们都希望好的生活。