查询词典 location parameter

Incidentally, the –recurse parameter is absolutely crucial here; leave it out and a Scripts folder will be created in C:\Test, but none of the files and folders in C:\Scripts will be copied to the new location; you'll create a C:\Test\Scripts folder, but there won't be anything in it.

在这里–recurse 参数是非常重要的。如果不加上它的话，C：\Test文件夹下仅仅会产生一个空的Scripts文件夹，而原来的C：\Scripts里的子文件则不会被复制进去。也就是说，这样做只会产生一个C：\Test\Scripts 文件夹，而该文件夹里是没有任何文件的。

When the parameter matching of the wheel location is improper, namely, the matching between the wheel toe-in and the wheel camber angle is ill-suited, abrasion of the two wheels of the same steering axle is inside or outside simultaneously, because of wheels sideslip. However, when double-front-axle steering system failure take place, abrasion of the two wheels of the same steering axle is in the same side, and that, tyre abrasion direction of front and back steering axles is rightabout. That is to say, if tyre abrasion of front steering axle lie in the left side, tyre abrasion of back steering axle lie in the right side to a certainty, which is the rule of tyre abrasion of double-front-axle steering automobile.

当定位参数匹配不当时，同一转向轴上左右车轮的磨损部位都在内侧或外侧，原因是左右车轮在滚动的同时还要产生相向或反向侧滑；而双前轴转向汽车前、后转向轴引导汽车转向方向不一致时，同一转向轴左、右车轮的磨损部位都在同一侧，而且前、后转向轴上的车轮偏磨损方向正好相反，即如果前转向轴左、右车轮磨损部位在左侧或右侧，那么后转向轴左、右车轮磨损部位就在右侧或左侧，这是双前轴转向汽车特有的轮胎磨损规律。

Secund abrasion is main format of abrasion about double-front-axle steering automobile and is different from secund abrasion caused by the parameter matching of the wheel location improperly.

双前轴转向汽车轮胎磨损的主要形式是偏磨损，这种偏磨损有别于车轮定位参数匹配不当时引起的偏磨损。

The effects of various optical coefficients(such as scattering and absorption coefficients, anisotropy parameter, etc.) and thermophysical properties(such as surface convective coefficient, etc.) and physiological coefficients(such as blood perfusion rate and metabolic heat generation, etc.) on the thermal behavior of the LILC method wet-c discussed in detail. The results show that the size and location of cauterized tissue under the skin can be bontrolled by properly adjusting the absorption and scattering coefficients and irradiation power and so on.

在此基础上，详细讨论了散射系数、吸收系数、各向异性系数等光学参数，激光加热功率、照射半径、表而对流换热系数等热学参数，以及血液灌注率和新陈代谢等生理参数对这种低损伤加热疗法的影响，结果发现，只要通过适当调节吸收系数、散射系数和照射功率等参数就可实现对加热区域位置和范围的控制。

The dose enhancement effects and decreasing effects caused by material inhomogeneity were studied quantitatively with a parameter named Dose Perturbation Factor, which was the ratio of the dose at a point in the heterogeneous phantom to the dose of the same spatial location point in the homogeneous phantom. It was showed that the degrees of the dose enhancement or decreasing depended on the energy of radiation, field sizes of the beamlets and compositions of the media. The dose perturbation for high energy X rays is greater than that for low energy X rays. At the same energy condition, the dose perturbation decreased when the field size increased. And the relationship between them was not linear.

模拟结果表明：在小射野情况下，异质组织界面处出现了较大的剂量跃变，剂量扰动效应的强弱程度取决于射线的能量、射野的大小和模体介质的不同等多种因素，高能X射线条件下的剂量扰动效应大于低能X射线条件下的剂量扰动；在入射X射线能量相同的条件下，剂量扰动效应随射野尺寸的减小而增强，并呈现一种非线性关系。

And the NC cutter location information file is produced to drive virtual NC system. The machining parameter optimization system of NC code is designed in the process of compiling NC code.

研究NC程序代码的分析处理方法和编译原理，并结合FANUC 0i数控系统的编程规范，设计了虚拟数控系统的NC程序代码编译器，实现了NC指令的插补算法。

In order to improve the condition of guide device of 3 500 mm finish mill and reduce the failure rate,a series measures were adopted: ameliorating hanging position of the guard plate,optimizing occlusal surface parameter of the uide wien guard tlate,altering guard plate location mode when changing roll,redesigning the bottom of guard sheet.

为改善3 500 mm精轧机导卫装置设备状况，减少故障，改进了护板吊挂方式，优化了导板与护板咬合面参数，改变了换辊时护板定位方式，重新设计了护板底部形状，消除了安全隐患，满足了高质量快节奏生产的要求。

Optimizing the model results in location the two edges of road which is represented as a vectorgraph by the parameter of parallel parabolas.

该模型的优化过程实现了道路的定位，得到的结果是平行抛物线的参数，实现了道路的矢量表示。

The paper researches two models for optimized management of slab-yard, and researches respective application about putting-in stock and model of taking-out stock. In the model of putting-in stock, the paper considered the cell of hot-rolling when making plan of putting-in stock, swings in the model of putting-in stock with the parameter 85, which indicates whether the slabs belong to the same hot-rolling cell. In the model of taking-out stock, The paper classed the slab-yard location according to the practice of the factory, based on which, the paper brings forward optimized turned-out algorithm founded on experts system, and the result of the experiments shows that the number of the turned-out pile is greatly reduced with the new algorithm.

文章重点研究了板坯库优化管理中的入库计划和出库计划编制问题，对两个决策模型：入库决策模型和出库决策模型进行了应用研究，其中在入库决策模型中，编制入库计划时就考虑了热轧工序轧制计划单元，在入库决策模型中添加&同一热轧单元&参数δ_5；在出库决策模型中，基于实际应用现场对板坯库库位进行分类，提出基于专家系统的板坯最优倒垛算法，实验结果表明提出的算法大大地降低了倒垛量。

The coupling between eccentric rotation and rigid-body vibration leads to many complex nonlinear terms, and the location of eccentric mass also is an important parameter.

偏心块的转动与刚体的振动相耦合将产生许多复杂的非线性项，偏心激励的位置也是一个重要的参数。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。