查询词典 load

After you create your load test, you can edit the load pattern in the Load Test Editor.

创建负载测试后，可以在负载测试编辑器中编辑负载模式。

This paper studies the influence of country economy guideline in power demand. According to identifying the main economy and society factors in affecting the change of Fujian power demand, the power demand forecast model is proposed. And the demand curve models fitting for diversified users are built by researching the influence of electrovalence to power demand.The influence of demand side management in load characteristic of Fujian power system is analysed.Used the arithmetic of modifying the history load curve, this paper forecast the changing and development trend of Fujian load characteristic.

本文研究了国民经济指标对电力需求的影响，通过识别影响福建省电力需求变化的主要经济社会因素，建立电力需求预测模型；研究了电价变化对电力需求的影响，对各类用户建立适合各自特点的需求曲线模型；分析了需求侧管理对福建电网负荷特性的影响，采用历史负荷曲线修正法，预测了福建电网负荷特性的变化发展趋势。

Secondly this dissertation made the statistical analysis of brittle ice load, and results showed that there was a greater variance of ice load during slow ice speed movement and a smaller variance of ice load during fast ice speed movement.

其次对冰脆性破坏时的荷载进行了统计，结果显示当冰速较慢时荷载的变化较大，而当冰速较快时荷载的变化较小。

Above all, consider combination of 3 kinds of load and different constant load and alterable load effect to compare an effect, gave out representative ferroconcrete component is in give an environment to fall, the affirmatory principle that the reliability of different operating period analysed methodological; to put forward intended performance structure to design reliability level, namely index of reliability of component part of the construction inside intended performance cannot be under the standard; of active standard on foundation of expression of design of reliability of our country structure introduce wear to fold decrease coefficient, gave out the affirmatory method of this coefficient, assure in design phase through this coefficient and achieve target of reliability of component part of the construction inside intended performance not the standard under active standard.

首先，考虑三种荷载组合以及不同恒荷载和可变荷载效应比影响，给出了代表性钢筋混凝土构件在给定环境下、不同使用期的可靠度分析方法；提出了预期使用期结构设计可靠度水平的确定原则，即预期使用期内结构构件可靠度指标不能低于现行规范的标准；在我国结构可靠度设计表达式基础上引入耐久性折减系数，给出了该系数的确定方法，通过该系数在设计阶段保证和实现预期使用期内结构构件可靠度指标不低于现行规范的标准。

To the same kind of rocks, the penetration rate increases with the increases of electric bit thermal power. When electric bit thermal power keeps fixedness, the penetration rate increases in various degrees with the increases of bit load in difference rocks. Increasing the bit load is beneficial to improve the quality of glass hole wall, but the bit load should not be too big.

对于同一种岩石，钻进速度随钻头电热功率的增大而增大；当钻头电热功率不变时，根据所钻岩石岩性的不同，钻进速度随钻头轴载的增大而不同程度地增大，增加钻头轴载有利于提高玻璃状孔壁的质量，但不宜过大。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.08-0.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.02-0.05 and 0.2 mm^3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2立方公厘左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.080.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.020.05 and 0.2 mm3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2 mm3左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

At last, 2KVA - experimental prototypes of AC power supplies of multiple-loop analog and digital control system have been made. Fast dynamic response and load compatibility have been verified by the experiment of step change in the load and under rated full-wave diode bridge rectifier load.

最后各研制了一台2KVA的多环模拟控制系统逆变电源实验样机和数字化控制系统逆变电源实验样机，切换负载实验和负载适应性实验分别验证了逆变电源系统具有良好的动态性能和负载适应性。

In this paper, the limit load of buried pipe, that is used in Nanjing city nature gas using engineering, was studied by finite element analysis under various groundsill character, pedestal angle and ground pressure, and the risk assessment for this piping was performed. The limit load of buried pipe was measured by experiments. The research contents and results were as follows:(1) With FEA method, the effects of various groundsill character, pedestal angle and ground pressure on the limit load of buried pipe were studied.

本文主要针对南京市城市天然气利用工程的埋地管道，研究其在不同地基性质、支座包角和地面载荷情况下的极限载荷，并进行了试验研究，同时进行了风险评价，主要研究内容与结论如下：(1)通过有限元计算分析，研究了不同地基性质、支座包角和地面载荷对埋地管道极限载荷的影响。

Derives the formulae for calculating the distortion and stress on the acting surface of flexspline load in the drive process of the harmonic gear drive with three-wave wavegenerator;(2) analyzes and compares the performance of plastic and steel products under light load drive and calculates the probably reached limit of drive ratio for both types of flexsplines under the same load;(3) applies the harmonic gear drive with three-wave wavegenerator to the small-sized multiple-revolution electric device of valves by taking into consideration of the low limit of the drive ratio for the harmonic gear drive with three-wave wavegenerator made of plastics, improves the design on the main drive mechanism of the traditional small-sized multiple-revolution electric device of valves, and validates through examples the feasibility for the harmonic gear drive with three-wave wavegenerator made of plastics to be applied to the small-sized multiple-revolution electric device of valves. Finally the author performs calculations on the two types of the flexsplines of the harmonic gear with three-wave wavegenerator by using the finite element method and analyzes the causes for the errors.

本文根据三波谐波齿轮传动的运动变形特点，采用弹性薄壳的力矩理论，推导了三波谐波齿轮传动柔轮载荷作用面上的变形及应力计算公式；分析比较了轻载传动情况下塑料和钢材的性能，计算了塑料制谐波柔轮和钢制谐波柔轮在相同载荷情况下可能达到的传动比极限；对塑料制及钢制三波谐波齿轮柔轮进行了有限元计算，分析了产生误差的原因；针对三波塑料谐波齿轮传动比极限低的特点，将之运用于小转矩多回转阀门电动装置中，对传统的小型多回转阀门电动装置的主传动机构进行了改良设计，并通过实例验证了三波塑料谐波齿轮传动在小转矩多回转阀门电动装置中应用的可行性。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。