查询词典 load

This error is returned if the module load command is used before loading a Multiboot kernel.

当模块加载命令在多重引导内核加载之前使用时返回此错误。

It is shown that the mechanical properties including Young's modulus, tensile strength, critical strain and stress under buckling can be enhanced with the decreasing of intershell spacing. The shear strength can be enhanced by 2-3 orders of magnitude when the intershell spacing is reduced to 20%, which is also dependent on commensuration. Zigzag-type carbon nanotubes have higher shear strength. The axial stress in tubes when the load transferring from outmost tube to inner tube is observed as well.

研究了单壁纳米管束横截面的六方化失稳现象，给出各种管径的面内压力－应变关系曲线；每条曲线都给出一个明显的拐点而且有很强的非线性；线弹性模量与参考构形有关，也受管直径的影响；分析了管束横截面的晶格不稳定性特征，表明晶格的缺陷能够明显的减小临界值；模拟了在不同应变下纳米管束对静水压的反应，发现不同压力下的截面形态不同，在很高压力下相邻管之间会形成化学键。

The experiments indicate that the comminution by impact or/and static load usually produces FSD particulate systems.

实验表明，可破碎物料的冲击式和静压式粉碎过程一般产生FSD颗粒体系。

So it is the base of this article to research the traffic signal control for the commix traffic, combined with practical reality. Urban artery usually bears the main traffic load.

城市干道通常承担着城市的主要交通流量，解决好城市干道的协调控制问题，能大大缓解交通拥挤压力。

However, this is rare and in fact it's common for multiple developers to share the load.

然而，这是罕见的，实际上它的多个开发人员共同分担负载。

In communication protocol's design of data structure and flow, the mechanism of load balance is used.

讨论了用时间片轮询访问的方法来取代设备的实时连接。

In order to drive a high impedance load such as HPM sources, it is necessary to commutate FCG's long pulse width, high-current and low voltage pulse to a short pulse with high voltage.

为用FCG驱动象HPM源这样较高阻抗的负载，必须使用脉冲功率调制电路把FCG产生的低电压、大电流、上升时间长的电压脉冲转化为高电压、上升时间短的脉冲。

The speed of this type of motor is controlled by the load and position of the commutator brushes.

在这种类型发动机的转速控制负载及整流子电刷的位置。

Formwork is a kind of temporary structure of multilevel force transfer, the force transfer route is usually as follow: load→form→inner ridge→outer ridge→post, after fixing the material of formwork, there are manifold possible compages of formation of formworks.

模板是一种多级传力的临时结构，传力路线一般是：荷载→模板面板→内楞→外楞→立柱，当模板的用料确定后，模板的构造有多种可能的组合。

Moreover, the effect of compensating capacitor on the load models is discussed.

在以上的负荷建模中还计及了补偿电容对负荷模型的影响。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"