查询词典 load-on

For sizes 30 thru 175 metric tons,breaking load is 5.4 times the working load limit.

注释：最大验证负荷为2倍工作极限 30t-175t破断负荷为5 4倍工作极限负荷；。

Note: 1. Except for basic load, we also produce JF35 series tie downs with breaking load of 2000kg.

注：1。除基本型负荷外，还生产破断负荷2000kg的JF35系列捆绑带。

Breaking Load—Load which causes fracture in a tensile, compression, flexure or Torsion

断裂负荷—在拉伸、压缩、弯曲或扭转试验中引起断裂的力。

Limit;for alloy steel hooks(S-320A)30t-60t:breaking load is 5 times the working load limit.

30t-60t安全系数为4倍工作负荷。

According to heat load source of die cavity, temperature distribution gradient equations and heat flux equations and the peak value equations of temperature load at die cavity surface have been obtained with research of temperature distribution and transfer laws of die surface by unsteady heat transfer theory.

摘要根据锻模型腔热负荷来源，通过非稳态传热理论，分析研究了模具工作表面层的温度分布与传递规律，给出了型腔表面温度分布梯度和热流密度公式，并给出了锻模型腔表面的温度负荷峰值的计算公式。

According to heat load source of die cavity, temperature distribution gradient equations and heat flux equations and the peak value equations of temperature load at die cavity surface have been obtained with research of temperature distribution and transf

摘要根据锻模型腔热负荷来源，通过非稳态传热理论，分析研究了模具工作表面层的温度分布与传递规律，给出了型腔表面温度分布梯度和热流密度公式，并给出了锻模型腔表面的温度负荷峰值的计算公式。

According to heat load source of die cavity, temperature distribution gradient equations and heat flux equations and the peak value equations of temperature load at die cavity surface have been obtained with research of temperature distribution and transfer laws of die surface by unsteady heat transfer theory.

新闻摘要：根据锻模型腔热负荷来源，通过非稳态传热理论，分析研究了模具工作表面层的温度分布与传递规律，给出了型腔表面温度分布梯度和热流密度公式，并给出了锻模型腔表面的温度负荷峰值的计算公式。

Comparing with the existing load balance in any point, analyzing the advantage and disadvantage of many tactics,In accordance with the effect and run environment of this CDN system, we have chose a a suitable local load balance tactic----HTTP redirector.

通过对现有的各种负载均衡技术的横、纵向对比，通过分析比较各种策略的优劣，以及结合本系统的用途及其所在的环境，提出了一种合适的局部负载均衡策略——HTTP重定向。

In order to function as a single compression member, the C-sections should be connected at a close enough spacing to prevent buckling of individual C-sections about their own axes parallel to the web at a load equal to or smaller than the buckling load of the entire section. For this reason, Sec.

为了起到单个抗压构件的作用，两段U型钢要贴得足够紧，以避免各段U型钢对平行于筋的自身轴的纵向弯曲——它是自身轴的荷载等于或小于整个断面的临界纵向荷载而造成的。

The effect of pole-arc coefficient、 air-gap、 damper winding and magnet circuit saturation for no-load property of harmonic winding by it . So, in this article, we bring forward a new idea and method to analyze no-load property of harmonic winding of synchronous generator by third harmonic excitation.

根据三段法，分析了极弧系数、气隙、阻尼绕组和磁路饱和等因素对谐波空载特性的影响，为分析谐波励磁同步发电机谐波绕组空载特性提供了一种新的思路和分析方法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。