查询词典 load with

In this paper, single phase bridge controlled rectifier circuit with resistance load and with resistance and inductance load had been simulated and analyzed in MATLAB.

本文使用MATLAB软件对带电阻负载和带阻感负载的单相桥式全控整流电路进行了仿真分析。

In order to meet the requirement of the Collector ring dipole superconducting magnet of FAIR in the process of operation, meanwhile, and to ensure the heat loads coming from the support structures to be lower than the design demands, the 3D models of support structures have been constructed with CATIA, then the calculation of low-temperature heat-load and the structure analysis have been done with ANSYS, the support structure material, 316LN+G10, is decided according to the heat-load calculation and the structure optimization, these results are necessary for manufacturing the formal magnet.

为保证FAIR收集环(Collector ring-CR)超导二极磁体工作过程中的磁场位形符合设计要求，同时保证由磁体支撑带来的热负荷小于设计要求，用CATIA软件建立了不同结构的磁体支撑3D模型，并用ANSYS有限元分析软件对建立的模型进行了低温热负荷分析和结构分析。通过比较分析的结果和对磁体支撑结构进行的进一步优化，确定了316LN+G10材料的支撑结构，为收集环超导二极磁体工程制造提供了参考。

Many condensers can fully deoxidize with the high load but has bad deoxidization performance with the low load.

许多凝汽器在高负荷下能充分地除氧，但在低负荷下除氧效果不良。

The finite element model of metal structure of FEH escalator was built with ANSYS software. Characteristics, load calculation and load combinations of the escalator were discussed. The software can show the biggest stress and distortion, which the engineer can compare with the standard requirement. It provided a theoretical basis for escalator metal structure design and material choosing.

利用ANSYS软件建立FEH公共交通型自动扶梯金属结构有限元分析模型，针对自动扶梯的特点对载荷进行分析，将载荷和约束施加于自动扶梯模型之上，通过软件计算出最大应力和最大应变值，以此判定是否满足标准要求，为FEH公共交通型金属结构的设计提供理论基础，也为降低成本提供参考依据。

Methods Six cadaveric lumbar vertebrae were harvested and evaluated with dual-energy x-ray absorptiometry and quantitative computed tomography to assess bone mineral density. Matched, polyaxial pedicle screws were then randomly assigned by side and placed using the Magerl, Krag or caudad trajectory technique assisted by Iso-C 3D scan and 3D navigation system. Cyclic loading tests were performed with a maximum 250 N load at 3 Hz up to 30000 cycles while recording load and displacement. Stiffness quotients were calculated it comparison.

从尸体中获取6节腰椎椎体经DEXA和QCT检测骨密度值，证实为骨质疏松后在计算机导航下按随机分组的方法向12个椎弓根中置人不同方向的椎弓根螺钉，使用MTS-858生物力学仪脊柱力学测试平台进行±250N的循环负荷疲劳测试，记录负荷循环中的螺钉位移，计算系统的刚度系数并进行对比分析。

A method for identifying the damage, using the influence line curvature of deflection differential values at a point before and after the damage is proposed, that is, when the moving load is in the area without the damage, the influence line curvature is zero, however when the moving load is in the area with the damage, the influence line curvature evidently increases and has the relationship with the positions of the damage points and the rigidity of the beam before and after the damage.

提出利用损伤前、后某一点的挠度差值影响线曲率来识别损伤的方法，即当移动荷载位于无损区域时，挠度差值影响线曲率为0，当移动荷载位于有损区域时，挠度差值影响线曲率明显增大，且与损伤点的位置、损伤前后的刚度有关。

Third, based on the example of over proof on-load loss in 180MVA/220kV power transformer, the eddy loss in winding is analyzed with the leakage flux element software. Some conclusions with practical use are given. In order to reduce the load loss, primarily we should reduce radial leakage flux of transformer possibily.

运用漏磁场分析软件，以180MVA/220kV电力变压器负载损耗超标为例，进行详细分析，提出有工程实用价值的结论：降低变压器负载损耗，从根本上应尽可能减少变压器辐向漏磁。

When is tested,testing shall be performed with rated load current of firstly, and then with load current of inverter.

在测试时（仅限 Power 测试），的额定负载电流，后带的负载电流。

By making ten health male athletic majors run on the programme-controlled jacger running platform with a progressive increasing load and with an unprogressive increasing load respectively,we have detemined the corresponding HR and HLa of the runners at various speeds.

通过10名体育专业健康男性大学生在Jacger程控跑台上分别进行有累进递增负荷与无累进递增负荷，并在实验中测定各档跑速时的相应心率和血乳酸值。

Motibity changed by gear-box in direction and rotate speed is transferred to the blade axis on the right side to drive the blade axis. blade axis'parameter, blade assembling frame and blade assembling means are ascertained. The load and movement of the blade axis are analyzed. And the best blade rotate speed is ascertained. According to the request of no-tillage soil, the appropriate furrow openers are chosen. They are staggered and assembled in two rows .According to the sliding cutting request, the crucial parts of the anti-blocking——the sliding cutting blade, its edge curve is analyzed and designed in principle. The academic curve function is gotten. Combined with working practice and technics request, the blade's figuration parameter is designed, 65Mn is chosen as the material for blades. The working load is analyzed. And the intension of the sliding cutting is analyzed and checked with ANSYS software. At last, the spring rack of the suppress wheal is analyzed in principle. The theory and parameter of designing the spring rack of the suppress wheal. Experiment indicated that the anti-blocking capability of this anti-blocking equipment was excellent.

设计出适合此防堵装置的动力传输方案，动力经变速箱变向变速后从右侧传给刀轴，驱使刀片切割秸秆；确定出了刀轴的参数、刀片的安装结构和安装方法，对刀轴的受力和运动进行了分析，确定出了刀轴最佳转速；根据免耕地的要求，选择恰当的开沟器，并采用双排错位安装的办法，避免了"瓶颈"现象的发生；根据滑切的要求对此防堵装置的关键部件——滑切刀片的刃口曲线进行了理论分析和设计，得到了刀刃的理论曲线方程；结合生产实践及工艺要求，设计出刀片的外形参数，选择65Mn作为刀片的材料；分析和计算了刀片在工作中承受的载荷，运用ANSYS 软件对滑切刀片的强度进行了分析校核；最后对镇压轮的弹簧支架结构进行了理论分析，提出了设计镇压轮弹簧支架的理论和参数依据。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。