查询词典 load displacement

In order to analyzes the soil deformation mechanism under the impact load of the step-bit, the finite element model of impact and displacement drilling with down the hole hammer is established on the basis of adopting Drucker-Pager yield criterion, taking soil as DP materials and simulating the drilling process by applying the impact load on soils.

为了分析阶梯钻头冲击挤密作用下土体的变形机理，将土体视为DP材料，服从Drucker-Prager屈服准则，通过钻具与土体之间的接触以及施加冲击载荷来模拟钻进过程，建立了潜孔锤冲击挤密钻进的有限元模型。

The paper focuses on the load distribution and load transfer among soil, pile-core and pile-socket, the interactive behavior of cement-soil ring and reinforced concrete core and some corresponding factors influencing the displacement of the pile which include the various core length, the section radius, the elastic modulus of soil and cement–soil etc.

着重分析了砼芯水泥土搅拌桩的竖向荷载在桩身内外芯和桩土各部分间的分配，砼内芯桩与水泥土外芯桩在荷载传递过程中的相互作用和共同工作特性，以及影响单桩沉降的因素包括砼内芯的直径和长度、水泥土和桩周土体的弹性模量等。

The results show that space finite analysis results are close to test ones, bottom chords suffer axial force and large in-plane bending, and the max stress is nearby each middle internode. The max stress of node crossbeams occurs in No.2 bottom flange, and that of internode crossbeams happens in ones lying in the middle of every internode. The concrete slab is in tension at the longitudinal direction, and also suffers bent at vertical loads. The degree of completely-composite model taking part in the combined actions is about 55%, while that of semi-composite model is 42%-43%. The combination of concrete slab and bottom chord increases the degree of floor system taking part in the combined actions, lightens the burden of bottom chord, and reduces out-of-plane bending of node crossbeams especially the ones near bridgehead. Stress and displacement of main truss can be evaluated by a equivalent plane rigid frame in preliminary design, and effective stiffness of bottom chords are composed of original ones and concrete slab, and the concentrated load from deck can be translated into uniform load.

研究结果表明：空间有限元分析结果与试验结果较吻合；下弦杆受到轴向拉力和较大的面内弯矩作用，各节间最大应力出现在节间中点附近；节点横梁最大应力发生在横梁2的下翼缘，节间横梁最大应力发生在位于端节间中部的小横梁上；混凝土板顺桥向整体受拉，并在竖向集中荷载作用下产生弯曲变形；全结合模型大部分节间内的桥面板参与主桁共同作用的程度为55%左右，半结合模型桥面板的参与程度为42%~43%；桥面板与下弦杆结合能够增加桥面板的参与程度，减轻下弦杆荷载，减少节点横梁尤其是靠近桥头横梁的面外弯曲；对桥梁进行初步设计时，主桁杆件的位移与内力可按照1个等效的平面刚架计算，下弦杆的等效刚度由原下弦杆截面和混凝土桥面板截面组合而成，桥面荷载可转化为均布荷载施加。

Then, safety analysis method was constituted considered the typical damage of concrete beam bridge. 5. By amending the reduction rate of loading capacity used in Code for Maintenance of Highway Bridges and Culvers (JTG H11-2004), a new reliable index is presented in the same safety standard to reflect the relation between load and resistance. According to the basic principal of calibration method, the recommended gradation index was computed under various factors such as different load combinations, vehicle operating status and different failure modes. With these calculated numerical values, the calculated reliability indexes standard for the estimation of safety degree of in-service concrete girder bridge members was ultimately obtained.6. Based on the related standards and results on crack and displacement that cannot continue to loading at home and abroad, the evaluation grade of the concrete beam bridge is proposed by analogy.

针对材料和构件损伤对混凝土梁式桥抗力的影响，基于材料和构件层次典型损伤的修正计算公式，在结构既有以及时变抗力评估的概率模型基础上，通过误差传递公式获得抗力统计参数，对抗力进行修正，构成了考虑混凝土梁式桥典型损伤的安全性分析方法。5、依据校准法原理，将《公路桥涵养护规范》(JTG H11-2004)中不同类别承载力下降率转化为修改分项系数，分别计算了轴心受压、轴心受拉、受弯、大偏心受压、受剪构件在各种情况下的可靠指标，根据破坏类型对校准结果进行分析，提出了基于可靠度的公路混凝土梁式桥安全性评定等级。6、基于不能继续承载的裂缝和位移的相关国内外规范和研究成果分析，通过类比提出了混凝土梁式桥不能继续承载的裂缝和位移评定等级界限。

Erection parameters in the literature [9] nonlinear analysis method used to calculate some of the variables erection capacity limit, but no major erection of some other variables, such as the level of the top-Ligan excess of the limit load length the impact of, and the top model Ligan more displacement constraints, and the actual situation of access to a certain extent; literature [7] space will be just as Falsework framework erection of the main parameters of the critical load, and The literature [10] scaffold for the ultimate strength estimation method for calculating the results of the amendment.

在搭设参数方面，文献[9]采用非线性分析方法，计算了部分搭设变量下的极限承载力，但是没有分析另外一些主要搭设变量如立杆超出顶层水平杆长度对极限承载力的影响，而且计算模型的顶部立杆位移约束较多，和实际情况有一定的出入；文献[7]将模板支架视为空间刚框架，分析了主要搭设参数下的临界荷载，并采用文献[10]提出的用于外脚手架极限承载力的估算方法对计算结果进行了修正。

Single factor experiments were done with the factors including the width of protrusion and the trolley's velocity, which showed that the surface frictional coefficient decreases with the width of protrusion increasing, and doesn't change with the trolley's velocity changing, which was consistent with the results of the orthogonal experiment. A theoretical model of the horizontal projection of a corrugated bionic surface's contact area was built, which showed that the contact area's horizontal projection decreases with width and interval increasing respectively and that the ratio of the contact area's horizontal projection and the vertical load decreases with the vertical load increasing. It indicated that the surface frictional coefficient decreases with the above three factors increasing respectively. Finite element modeling and analysis of interactions of a plate and soils was done using ANSYS, which showed that the plate frictional coefficient is little relative to soil elastic modulus and decreases with vertical surface pressure and that trolley's pull and vertical displacement of bionic surface's control pilot keep constant almost during the plate being pulled. Finite element modeling and analysis of interactions of a corrugated bionic surface and soils was done using ANSYS, which showed that surface frictional coefficient is little relative to soil elastic modulus and decreases with bionic surface's structural parameters and vertical pressure increasing. However, the three factors all didn't affect the surface frictional coefficient remarkably on the condition of 90% dependability. For the first time, bionic surfaces were applied to screw piles, which formed bionic screw piles, and the contrast experiments showed the bionic screw pile had certain resistance-decreasing effects.

建立了波纹型仿生曲面与土壤的接触面积的水平投影的理论模型，表明接触面积的水平投影A随着波纹型仿生曲面突起宽度、两相邻突起间距的增大而减小，接触面积的水平投影与波纹型仿生曲面表面垂直载荷之比随着波纹型仿生曲面表面垂直载荷的增大而减小，进而得出仿生曲面摩擦系数随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小；利用ANSYS软件对平板与土壤的相互作用进行了有限元建模与分析，表明平板摩擦系数与土壤弹性模量关系不大，而随着表面垂直载荷的增大而减小；平板牵引过程中台车牵引力和仿生曲面控制节点垂直方向位移基本保持不变；利用ANSYS软件对波纹型仿生曲面与土壤的相互作用进行了有限元建模与分析，表明波纹型仿生曲面系数在一定范围内基本不受土壤弹性模量的影响，随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小，但在可信度为90％的前提下，三个因素影响都不显著；首次将波纹型仿生曲面应用于与土壤作用方式以挤压为主的螺旋桩，形成仿生螺旋桩，并与普通螺旋桩进行了沉桩对比试验，表明波纹型仿生曲面应用于螺旋桩桩体表面具有明显的降阻作用。

The main research contents are as follows:1. Through massive calculation, analysis and comparison, sum up the similarities and differences between the special-shaped cross sections and rectangular cross sections in mechanical features, between reinforced concrete special-shaped columns and rectangular columns in load-bearing capacity, ductility performance and provide necessary basic concepts and data for further understanding the characteristics of the special-shaped columns;2. Through massive elastic calculations and elasto-plastic analysis, under the preconditions of satisfying the code's requirements for axial compression ratio, limit value of lateral displacement and load-bearing capacity of normal section,oblique section and beam-column joint, under circumstances of different intensity of earthquake, structure dead weight, sort of site and column grid bay dimension, the variation regularity of maximum suitable height of structure, and thus sum up the maximum suitable height of structure for code for the purpose of macro-control while deciding the design scheme;3. Make a preliminary study on the stress feature of reinforced concrete special-shaped column and Z-shaped column of which the ratio of limb length to limb thickness is between 4~5 ,and the preliminary design method is suggested;4. Through elato-plastic time history dynamic analysis of typical projects, check up the weak storey of the special-shaped column structure and yielding, breaking and collapse mechanism to satisfy the earthquake resistant requirement to buildings of remaining stand under strong earthquake;5. Derive for project use simplified calculation formula of vibration period, suitable vibration period, suitable rigidity of special-shaped column structure through theoretical analysis, and provide an easy and practical method for deciding the structure scheme economically, safely and reasonably;6. Based on the study achievements in theory and massive analysis and calculations of this paper, sum up the regularities of inner force, deformation of special-shaped column structure and seismic conceptual design, and thus the suggection of seismic design of special-shaped column structures is presented.

本文研究的主要内容如下：通过大量的计算、分析和对比，总结出异形截面与矩形截面在力学特性、钢筋混凝土异形截面柱与矩形截面柱在承载能力、延性性能等方面的异同，为深入了解异形截面柱的特点提供必要的基本概念和数据；通过大量的弹性及弹塑性计算分析，在满足规程对轴压比、侧移限值及正截面、斜截面、节点承载力抗震验算要求的前提下，在不同抗震设防烈度、结构自重、场地类别及柱网开间尺寸情况下最大适宜高度的变化规律，并在此基础上总结归纳出异形柱结构的最大适用高度规定，可用于规程，以便于在确定方案时起到宏观控制的作用；对肢长与肢厚比在4～5的钢筋混凝土异形截面柱及Z形柱的受力特点进行初步探讨，提出初步的设计方法；通过对典型工程的弹塑性动力时程分析，检验异形柱结构的薄弱层及屈服、破坏、倒塌机制，以达到建筑物大震不倒的抗震设防要求；通过理论分析，推导出异形柱结构自振周期，以及适宜自振周期、适宜刚度的工程实用简化计算公式，为经济、安全、合理地确定结构方案提供简便实用的方法；在本文理论分析、计算以及大量的研究成果基础上，总结归纳出异形柱结构内力、变形的规律及抗震概念设计内容，并在此基础上提出异形柱结构的抗震设计建议。

Uses the biggest strength training method (80%～100% biggest strength) adding 30% biggest strength load training method; the load combination method to make the acclivity to lie pushes the barbell training, good in uses; the biggest strength training method to the upper limb shot fast strength training effect (80%～100% biggest strength) adding the unarmed quickest speed training method and the biggest strength training method (80%～100% biggest strength) adding 60% biggest strength shoulders the training method the load combination method.

用"最大力量训练(80％～100％最大力量)+30％最大力量负荷最快速度训练法"负荷组合方法做上斜卧推杠铃训练，对推铅球上肢快速力量的训练效果好于用"最大力量(训练80％～100％最大力量)+徒手最快速度训练法"与"最大力量训练(80％～1 00％最大力量)+60％最大力量负荷最快速度训练法"负荷组合方法。

The method which is used to measure and compute moment, yield and turning angle by steel bar gauge is introduced in detail. According to the measuring results, the horizontal critical load of the testing pile is 120 kN. The steel bar gauge measuring results show that the largest moment is located in the depth from 2 m to 3 m under the horizontal load, it transfers to the deeper location with the increase of the horizontal load, and the bend distortion only occurs in the upper of 1/3 pile length.

结合实际工程详细地介绍了利用钢筋计测试水平荷载作用下桩身弯矩、挠度和转角分布的方法，根据桩顶位移和钢筋内力测试结果判定试验桩的水平临界荷载为120 kN；根据钢筋计测试结果可知，在水平荷载作用下，桩身最大弯矩截面位于在地面以下2～3 m处，且随着荷载的增大最大弯矩截面逐渐向深部转移；发生弯曲变形的部分主要是桩长1/3以上的桩体，而其下的桩体几乎不发生变形。

A ultra-short term load forecasting method based on autoregression;2. A novel method called load derivation is introduced for ultra-short term load forecasting of power system.

仿真表明了改进模型的有效性和算法的可行性，对于超短期负荷预测这类需要反应迅速的问题，采用本文提供的方法进行预测是可靠且非常有效的。

In contrast to the ubiquitous rising-sun-with-rays military flag of the Japanese, Chinese banners and ensigns feature a range of designs.

与遍地都是的太阳军旗不同，中国人的旗帜和徽章设计得各式各样。

From their small corner of Feng's Guangzhou headquarters -- a jumble of pink leashes, squeezable rubber steaks, and plastic doggy Santas for Fido's stocking -- Soleil's designers come up with at least five new products a month.

从Feng 设在广州总部的产品展示柜台上可以看到，Soleil的设计师每月至少设计出5件新产品。