查询词典 liquid metal

Based on these studies, the design and realization of software and hardware for monitoring ACD and liquid metal wave are investigated in detail, and the three reasons of liquid metal wave are given.

在此基础上，对极距和铝液波动的在线监测系统的软硬件组成及系统的应用进行了深入地研究，并提出了铝液波动的三种原因。

Liquid sodium boiling thermal—hydraulic characteristics and its two—phase flow instability is one of the most important research topics to Liquid Metal Fast Breeder Reactor .

液态金属钠沸腾特性及其流动不稳定性对于快中子增殖反应堆的运行及安全分析至关重要。

The flow of molten metal are the forefront of the lost foam pyrolysis products, it will happen with the liquid metal reflect and affect the quality of metal liquid, if the liquid metal filling process in pyrolysis products should not rule out smoothly, it is easy to cause stomatal , Cockle, by defects such as carbon.

金属液的流动前沿是热解的消失模产物，它会与金属液发生反映并影响到金属液质量，如果金属液充型过程中热解产物不能顺利排除，就容易引起气孔、皱皮、增碳等缺陷。

Chip cooling ; nanofluid ; nano liquid metal fluid ; nanofluid heat pipe ; nano-liquid droplet ; heat transfer enhancement ; fluidics control

芯片冷却；纳米流体；纳米金属流体；纳米流体热管；纳米液滴；强化换热；流体控制

The electromagnetic pressure produced by the counteract of magnetic field in coil and the eddy current in liquid metal is ma inly determined by the magnetic flux density on the surface and its dissipation in the liquid metal.

在分析液态金属电磁成形理论模型的基础上确认：作用在液态金属表面的电磁压力和加热密度主要取决于其表面上磁场的大小以及磁场在液态金属中的分布规律。

It is the first time and elementary to prove it is right that the"liquid micromulti-phase structure model"is suit to unlimited solubility solid solution system by the structure analysis of liquid metal X-ray diffraction and theory calculation on Cu〓Ni〓 alloy liquid and undercooled liquid between its liquidus and solidus.

通过对Cu〓Ni〓合金在两相区过冷状态下的液态X-射线结构分析和理论计算，首次初步证实了"液态微观多相结构"模型适合于固态无限固溶体系这一思想的正确性，但由于实验的难度未能用多种合金进行考核，这是我们今后要进一步做的工作。

The dynamics model for the simulation of liquid aluminum alloy in the porous medium is established as the following: x〓=〓 The viscous frictional resistance and additional resistance caused by the liquid metal surface tension when the liquid metal is infiltrating have been fully considered in this model.

在该模型中充分考虑了液态金属渗流时受到的粘性摩擦阻力、液态金属表面张力引起的附加阻力对渗流的影响。

Zirconia/graphite compound mold core was prepared by the coating, in which the silicon sol was used as binder and zirconia was used as refractory materials. The application feasibility of metal particles as a coolant in the solidification process was studied, and the application of metal particles as subsidiary coolant in the liquid metal cooling of directional solidification were analyzed and studied in this investigation. The conclusions can be drawn as follows: 1 The zireonia/graphite compound cores fabricated by brushing coating which was prepared by making silicon sol agglutinated zirconia as a refractory material were casteded at 800℃and 1000℃respectively, and the results show that the strength of the mold core is strong enough to meet the requirement of practical casting.

本文研究了以硅溶胶为粘结剂，氧化锆为耐火材料来制备氧化锆／石墨复合型芯的制备工艺；并分析了金属颗粒作为冷却剂在金属凝固过程中应用的可行性、金属颗粒的冷却能力以及金属颗粒作为辅助冷却剂在定向凝固的液态金属冷却法中的应用，得出以下结论：(1)以硅溶胶为粘结剂，氧化锆为耐火材料来配制涂料，采用刷涂石墨型芯的方法来制备的氧化锆／石墨复合型芯经800℃和1000℃实际浇铸实验，结果证明型芯的强度足够满足实际浇铸要求。

The flow status of liquid metal in the sand box of group casting was discussed according to the fluid mechanics and heat transfer theory. Not only does the appearance of vying liquid metal happen when group casting between the big and small castings, identical castings in the multiple gates system appear too, even one casting.

运用流体力学、传热学原理，分析群铸时液态金属在各型腔内的流动情况，揭示出争铁液现象不仅在大小件混铸时发生，在多个内浇道浇注系统中群铸相同铸件，甚至仅一个铸件仍存在这一现象。

In boiler field, proper atomization of high viscosity liquid fuel is the essential assurance to safe .stable and high efficient combustion for boiler; in the propulsion equipment of rockers and turbo jet-propelled engine, the atomization quality of liquid fuel is the precondition to improve combustion efficiency and supply sufficient propulsion; in the field of industrial manufacture, metal powder is made by liquid metal which is impacted by high velocity gas; in the field of agricultural irrigation, the water with certain velocity is used to strike metal disk to make insufflations proportionally to the irrigation field; in the technique of desulphurization and coal gasification, proper design of nozzle is the essential factor to advance the efficiency of desulphurization and coal transformation.

在锅炉领域，高粘度液体燃料的良好雾化是锅炉安全稳定高效燃烧的重要保证；在火箭推进装置、涡轮喷气式发动机中，液体燃料的雾化质量是提高燃烧效率并产生足够推力的前提；在工业生产领域，用高速气流冲击液态金属来制备金属粉末：在农业灌溉中，用一定速度的水流冲击金属圆盘破碎并改变方向实现对灌溉区域的均匀喷洒：在烟气脱硫、煤气化等工艺中，良好的喷嘴设计是提高烟气脱硫效率和碳转化率的重要因素。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。