查询词典 limit of error

The pattern of camber die-drawing are optimized. The physical innate character of drawing with camber die is analyzed thoroughly. For the first time, the periodical relation between the limit drawing coefficient and the large longitudinal stress in dangerous section is established. Furthermore, the rationale to judge limit deforming degree is developed. Then, the limit drawing coefficient of drawing with camber die is proposed. Based on the criterion that the large stress in flange is smaller than that of limit value, the formula of drawing with camber die without wrinkles is deduced.

对拉深凹模的型式进行了优化；深入地分析了曲面凹模拉深成形的物理本质，首次定量地确定了极限拉深系数与危险断面最大径向应力的关系，提出了判断极限变形程度的依据，分析了极限承载能力，建立了曲面凹模拉深的极限拉深系数的表达式；以凸缘切向最大压应力小于凸缘切向压应力临界值为准则，推导出了曲面凹模拉深不起皱的理论表达式。

Article 14 In the case of applying for extending the time limit for the re-importation and re-exportation of goods, the holder of ATA carnet or consignor or consignee of goods temporarily imported or exported under non-ATA carnet shall, not later than 30 days prior to the expiry of the prescribed time limit, apply to the customs office which examines and approves the temporary importation or exportation of goods for extending the time limit and submit an Application for Extension of the Time Limit for the Goods Temporarily Imported / Exported (See format in Annex 4) and other relevant application materials.

第十四条暂时进出境货物申请延长复运出境、进境期限的，ATA单证册持证人、非ATA单证册项下暂时进出境货物收发货人应当在规定期限届满30日前向货物暂时进出境申请核准地海关提出延期申请，并提交《货物暂时进／出境延期申请书》（格式文本见附件4）以及相关申请材料。

The experimental results showed that the diameter of orifice had a great effect on the lower limit of the hung-up regime but not on the upper limit. However, the stagnant height in hopper, the angle of hopper, the length and diameter of standpipe had influence on the upper limit but not the lower limit.

实验结果表明：立管底部孔口大小对于悬料区的下限有影响，而对上限无影响；相反，漏斗中的物料高度、漏斗的锥度、立管长度和立管直径对悬料区的操作有很大影响。

The results show that under the complicated upper limit control logic,the upper limit depth trajectory is not a simple form,but two or more irregular forms of re-entering into the upper limit depth,or regular oscillation form around the upper limit depth.These results may be expected to provide a theoretical basis for analyzing the problem in sea trial.

仿真结果表明，在复杂的上限控制逻辑下，上限深度弹道不是一种形式，可能存在不规则的2次或多次再进入上限的弹道形式，或者存在上限附近深度规则振荡的弹道形式，这些规律为实航中出现的一些特殊现象分析提供了理论依据。

Must achieve this short-term buying stockthe goal, the investor should formulate an upper limit and the lower limit generally on some stock price, but in the stock achieved when upper limit undersells, falls to the lower limit time buys.

要达到这一短期的炒股目的，投资者一般应就某一个股票的价格制定一个上限和下限，而在股票达到上限时就抛售，跌至下限时就购入。

And the error limit of flux sensor under 5%, the error limit of intelligent Heat Meter up to grade 2 according to the precision criterion of heat meters.

基于MSP430单片机的智能热量表满足《中华人民共和国城镇建设行业标准CJ128-2000热量表》的标准要求，电源采用内装3.6V锂电池，使用寿命超过八年；流量传感器误差限不超过5％，总体热量表精度达到2级精度标准。

For the all classes of dies, if we analyse the fluctuate, tendency of increase and decrease and law which appeared in the die's whole life, we will find that the master of the error are changeless; the error that because the abrade of the cutter and impression will be as the cutter grinding times increased at the same time. And that will cause the error oversize gradually; and also have another part error are unconventional , unforeseen.

对各类冲模冲件误差在冲模整个寿命中出现的波动、增减趋向及规律等进行全面分析便可发现：冲件误差的主导部分是不变的；因刃口或型腔的自然磨损而出现的误差增量随冲模刃磨冲数增加而使这部分误差逐渐加大；还有部分误差的增量是非常规的、不可预见的。

Because of fault in operation and the precision of instrument,the defect error and accidental error are involved in the procession of data collection,the defect error that are brought by mistakes of people and influence of outside is large,the contingency error that are inevitably and randomicity is little.

在采集数据过程中，由于某些操作或仪器原因，往往使数据中包含人为错误，或外界干扰产生的量值较大的"过失误差"以及不可避免的带随机性质且量值较小的"偶然误差"。

After analyzing the main error sources in the system, it discusses the error separation and error compensation of parts of the error source.

在分析了系统的主要误差源后，本论文重点研究了部分测量误差的分离补偿与修正。

Error analysis of digital instruments on their characteristic parts including sample/holder circuit error and analogue/digital convector error was reviewed in this paper. With the help of some examples and data tables, error origins and the synthetic method were discussed.

评价了数显仪特征部分误差分析方法，包括：采样／保持电路、模数转换单元的误差，并通过典型例子和列表数据分析了多种误差源及其综合计算方法。

Objective:To explore the feasibility of laparoscopy in diagnosing and treating of abdominal diseases.

目的：探讨腹腔镜用以诊断腹部外科疾病及选择治疗方案的可行性。

The lifetime of nylon 1010 and nylon 1010/POSS composites decreased with increasing temperature.

热重-红外联用分析表明尼龙1010在氮气气氛下的降解产物主要为小分子的低聚物，POSS并不改变尼龙1010降解产物的组成。